使用ip nat source 实现内网服务器不设置网关与外公网用户通信
推荐
原创
2013-08-01 17:26:27
10000+阅读
点赞
10评论
主要介绍ip nat inside source 和 ip nat source的用法在NAT的转换过程时数据包处理过程的不同
原创
2013-08-07 14:08:40
10000+阅读
点赞
12评论
今天为大家演示的是动态NAT:首先要定义合法地址池,然后采用动态分配的方法映射到内部网络。动态NAT是动态一对一的映射。
动态NAT拓扑:
IP地址规划:
R1--F0/0=202.96.1.1/24
---F0/1=192.168.1.254/24
R2--F0/0=202.96.1.2
原创
2009-12-01 17:12:52
10000+阅读
点赞
4评论
ip nat inside source Translates the source of IP packets that are traveling inside to outside.Translates the destination of the IP packets that are traveling outside to inside.ip nat outside source Tr
转载
2007-08-28 18:19:39
613阅读
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname nat-r1
!
enable secret 5 $1$FEQr$INhRecYBeCb.UqTQ3b9mY0
!
ip subn
转载
精选
2008-10-16 19:35:38
551阅读
实验拓扑
在SA上配置:
激活端口:
在RA上配置:
在SB上配置:
在RB上配置:
在PC1上配置:
在PC2上配置:
在RA上配置:
在RB上配置:
在RA上配置:
在RB上配置:
在RA和RB上配置占先权:
进行端口跟踪:
查看:
关闭端口重定向:
原创
2009-08-19 21:30:04
1280阅读
点赞
1:inside代表inside -> outside,outside则意味着outside -> inside。方向不通,会影响包是先路由还是先转换地址。
原创
2017-02-13 21:44:11
1262阅读
一、 NAT简介
NAT(Network Address Translation)的功能,就是指在一个网络内部,根据需要可以随意自定义的IP地址,而不需要经过申请。在网络内部,各计算机间通过内部的IP地址进行通讯。而当内部的计算机要与外部internet网络进行通讯时,具有NAT功能的设备(比如:路由器)负责将其内部的IP地址转换为合法的IP地址(即经过申请的IP地址)进行通信。
二、 N
原创
2010-09-03 10:47:24
334阅读
CCNA之access-list实验基础篇
当数据包经过路由器的时候,使用访问列表能够过滤数据包,它是一种网络层的安全手段。在CCNA中我们只关注ip access-list ,依据使用用途分为standard access-list 和extend access-list
R1------------
转载
2012-03-26 14:10:59
1215阅读
NAT三种模式
静态转换(一对一,双向通信,内外网可互ping)
动态转换(多对多,单项通信,内ping外通,外ping内不通)
端口多路复用(多对一,单项通信)
实例:
SW2配置
Switch>en
Switch#conf t
Switch(config)#hostname SW2
SW2(config)#interface f0/1
SW2(co
原创
2013-04-26 10:15:59
1177阅读
点赞
2评论
CISCONAT配置命令21.1.在路由器上启用基本的NAT功能Router#configureterminal‘进入全局模式Enterconfigurationcommands,oneperline.EndwithCNTL/Z.Router(config)#access-list15permit192.168.0.00.0.255.255'建立访问控制列表Router(config)#ipnat
原创
2013-11-12 10:23:32
452阅读
Inside network: 3.3.3.4 (static to 2.2.2.24 outside) 3.3.3.5 (static to 2.2.2.25 outside) | | | 3.3.3.1 (ethernet 0) Router - the_lorax 2.2.2.1 (serial 0) | | | Outside net
转载
2008-08-22 16:03:04
409阅读
三条命令IP NAT INSIDE SOURCE LIST 1 POOL ABC OVERLOAD 可以一个外网地址对应多个内网地址(不同端口)
原创
2016-07-09 10:21:18
970阅读
CiscoNATIOSrouterInside-----outsideNATNPAT内网----外网(动态)ipnatinsidesource….StaticNATStaticPAT外网—内网ipnatinsidesourcestatic….以上其实内网--外网inside方向sourceNAT发布外网服务器也是从内网inside看source其实应该从外网逻辑上outside看destinat
原创
2018-09-21 09:33:25
890阅读
实验目的:1、熟练掌握静态NAT、动态NAT、PAT的使用方法实验要求:1、服务器1使用静态NAT映射公网IP 10.1.1.3 2、服务器2使用静态NAT映射公网IP 10.1.1.4,仅能使用web服务(80端口) &
原创
2022-05-06 17:41:07
3063阅读
点赞
动态NAT拓扑图如下:实验步骤1、设置三层交换机swsw#conftEnterconfigurationcommands,oneperline.EndwithCNTL/Z.sw(config)#noiproutingsw(config)#2、设置路由R1R1#conftEnterconfigurationcommands,oneperline.EndwithCNTL/Z.R1(config)#in
原创
2019-10-17 12:09:12
686阅读
点赞
ip nat inside source
Translates the source of IP packets that are traveling inside to outside.
功能1:将从内到外的IP包的源地址进行转换(将内部局部地址转换为内部全局地址)
Translates the destination of the IP packets that are
转载
精选
2012-02-29 12:00:33
1987阅读