IAD108/208作为VoIP/FoIP媒体接入网关,应用于NGN用户接入层,完成模拟话音与IP包之间的转换,并通过包交换网络传送数据的功能,同时还可通过标准SIP/MGCP(Media Gateway Control Protocol)协议,与华为技术有限公司SoftSwitch软交换设备配合组网,在SoftSwitch控制下完成主被叫间的话路接续。
总体规格
|
技术标准
|
ITU-T(International Telecommunication Union - Telecommunication Standardization Sector) G.711 μ-Law(64kbit/s)
ITU-T G.711 A-Law(64kbit/s)
|
外部接口
|
RJ11型POTS接口:提供8路(仅108)
RJ-45型10M/100Base-TX用户接口:提供2路/8路
RJ-45型上行接口:提供1路
RS232本地维护串口(Console):提供1路
|
用户最大容量
|
IAD108系列:提供8路POTS用户和2路数据用户
IAD208系列:提供8路POTS用户和7路数据用户
|
华为U-SYSIAD系列具备接口丰富,其端口:容量从1端口至32端口,同时具有语音
数据端口合一的IAD,适应不同的用户需求,产品系列业界最全。支持完整PSTN业务,具备可管理可维护的电信级特点。
丰富的上下行接口下行业务接口:
– POTS接口,接入语音用户最大可达32路
– FE接口,提供以太网数据接入功能,支持IAD级联
– FXO 接口,支持FXO接口旁路PBX话音业务,支持根据号首选择路由
– RS232串口,提供本地串口维护功能
上行接口:
– FE:上接LanSwitch,语音数据一根线上行出口
– 光口:提供单/多模100 M光口,楼道IAD上行接光纤拉远,组网应用灵活
– XDSL接口:上行支持ADSL/VDSL接口,组网灵活,覆盖范围广
完善的业务支持能力
– 支持语音、传真、MODEM业务
– 支持各种话音基本业务和补充业务
– 支持卡号等智能业务
– 支持使用FXO进行语音业务的IP旁路
– 支持IP半永久连接业务
丰富的协议支持
– SIP、MGCP、H.248、H.323协议
– 支持SNMP网管协议
– 支持DHCP协议,动态分配IP地址
– 支持FTP、TFTP协议、支持Xmodem协议
– 支持G.711、G.729、G.723等多种语音编解码和编解码动态切换功能
– 支持T.30和T.38协议,保证传真业务在IP上的实现
– 支持Telnet协议,提供CLI命令行接口
先进的语音算法
华为系列化IAD支持各种业界各种先进的语音算法,提供高质量的语音保证。
– 语音激活检测(VAD)
– 舒适背景音生成(CNG)
– Jitter Buffer动态调整,最大可达120ms
– 64ms的回波消除(满足ITU-T G.165/G.168)
– 丢包补偿技术
– DTMF检测/生成
– 可选TX/RX增益控制
电信级可靠性设计
1)设备可靠性设计
– 具有完善的故障检测、网管告警功能。系统自动进行检测,如发现故障可以通过网管进行告警,以降低故障恢复时间,同时,还有电源监控、温度监控、噪声控制(根据温度进行风扇控制)等功能进行电源故障检测。
– 电源、接口部分具有过流、过压保护
– 采用WDT技术,当软件发生异常或故障时,可以进行恢复
– 所有插板支持热插拔,当产品出现故障现象时,可以对业务、上行插板进行更换,或对系统进行复位操作
2)网络可靠性设计
– 支持国标IAD业务认证流程。通过软交换与IAD之间严密的认证流程,杜绝非法IAD的接入
– IAD本身具备ACL访问控制功能过滤非法报文的攻击;在受到网络攻击时,能够进行过载控制和网络正常后的自动恢复功能
– IAD具备日志功能,可记录系统维护、运行信息、调试信息等,便于调试维护
可管理可维护
– 支持NGN网络的用户线测试功能,为远程故障定位提供强大支持
– 既可以通过超级终端进行本地管理,也可以通过Telnet、基于Web的方式实现远程管理
– 支持统一网管,与核心设备共用iManager N2000综合网管
电源输入
100 V – 240 V AC, 12V3A DC, 50 Hz – 60 Hz, 支持远供
整机功耗
上行峰值功耗/以太网上行峰值功耗:
IAD108系列:DSL 20.37W /17.6W
IAD208系列:DSL 21.37W /18.6W
运行温度
长期工作:0℃~+55℃
相对湿度
长期工作:5%~85%(非凝结)
短期工作:0%~90%
外形尺寸
283mm(宽)×206mm(深)×57mm(高)
整机重量
500g
LED 指示灯
PWR, RUN, WAN,Tel1-8
IAD(Integrated Access Device)108/208综合接入设备是华为技术有限公司下一代网络NGN(Next Generation Network)解决方案中的重要部件,用以向公司等用户提供小容量VoIP(Voice over IP)/FoIP(Fax over IP)解决方案。
IAD208E(M)
Overview
The IAD208E(M) interconnects with the SoftCo through the standard SIP protocol and provides eight data-and-voice integrated user interfaces.
Product Positioning
The IAD208E(M) is at the edge access layer of HUAWEI unified communications. By adopting the standard voice codec and compression techniques, the IAD208E(M) encodes voice signals, encapsulates them into IP packets, and then sends the IP packets to a specified media gateway through the IP network. After the IP packets reach the destination, the destination IAD performs the reverse processing to restore the packets into voice signals. In this way, the VoIP and FoIP functions are achieved.
The IAD208E(M) connects to up to eight POTS and data users at the same time and thus voice and data are integrated based on standard category 5 cables. At the user side, a user interface is connected to an RJ-11 FXS interface and an RJ-45 data user interface through a junction box; at the network side, the upper-link interface connects to the IP network in 10Base-TX or 100Base-TX mode.
Figure 1-1 shows the networking involving the IAD208E(M) and the SoftCo.
Figure 1-1 Networking involving the IAD208E(M) and the SoftCo
Main Functions
- The IAD208E(M):
Connects POTS users to the IP network.
Connects data users to the IP network.
Supports T.38 fax service and transparent fax transmission.
Supports transparent transmission of modem signals.
Supports the PPPoE.
Supports the power over Ethernet (PoE).
Supports the traditional PSTN phone services, such as CLIP, call forwarding, and call waiting.
Cooperates with the SoftSwitch to obtain intelligent and feature services, such as the RBT, ONLY service, and card service.
Product Appearance
The appearance of the IAD208E(M) is similar to a box, as shown in Figure 1-2 .
Figure 1-2 Appearance of the IAD208E(M)
Technical Specifications
Table 1-1 lists the technical specifications of the IAD208E(M).
Table 1-1 Technical specifications of the IAD208E(M)
Parameter
|
Specification
|
Maximum user capacity
|
Eight POTS and data users
|
BHCC
|
500
|
Call put-through rate
|
> 99%
|
MTBF
|
> 2.3 years
|
Dimensions
|
283 mm in width, 206 mm in depth, and 57 mm in height
|
Weight
|
0.5 KG
|
Power voltage, current, and frequency
|
Input: 100-240 V AC, 1 A, 50 Hz or 60 Hz
Output: 12 V DC, 3 A (maximum current)
|
Maximum power consumption
|
36 W
|
|