python lcd1602驱动 python驱动器

python驱动电机部分完结，现在把全部代码公布，基本实现驱动器速度控制部分功能。接下来我将把电机驱动器移植到ROS上，实现驱动器与ROS之间的通讯。下图为我代码的基本框架：

#!/usr/bin/env python

import serial
import time
import threading
import struct

motor_speed_mode = b'\x02\x00\xC4\xC6'
motor_status = b'\x80\x00\x80'
motor_start = b'\x00\x00\x01\x01'
motor_stop = b'\x00\x00\x00\x00'

class SpeedMotor:
    def __init__(self, device,speed):
        # 真实速度
        self.rel_speed = 0
        # 设置的速度
        self.set_speed = speed
        # 运行状态
        self.run = False
        # 故障状态
        self.fault = None
        # 电机电压
        self.voltage = 0
        # 电机电流
        self.current = 0
        # 设置串口通讯
        self.serial = serial.Serial(device, 57600)
        self.serial.timeout = 0
        # 开启读数据线程
        threads = []
        t1 = threading.Thread(target=self.read_motor)
        threads.append(t1)
        t2 = threading.Thread(target=self.send_motor)
        threads.append(t2)
        for t in threads:
            t.start()
        # 设置为速度模式
        self.serial.write(motor_speed_mode)
        time.sleep(0.1)
        # 设置加减速度
        self.serial.write(b'\x0A\x14\x14\x32')
        time.sleep(0.1)

    def motor_speed_set(self):
        a1 = 6
        a4 = check_code(a1, self.set_speed)
        self.serial.write(struct.pack(">BhB", a1, self.set_speed, a4))

    def set_status(self):
            self.serial.write(motor_status)
            time.sleep(0.2)

    def motor_start(self):
        self.serial.write(motor_start)
        self.run = True

    def motor_stop(self):
        self.run = False
        self.serial.write(motor_stop)

    def read_motor(self):
        while True:
            n = self.serial.inWaiting()  # 等待数据的到来，并得到数据的长度
            if n:   # 如果有数据
                n = self.serial.read(n)  # 读取n位数据
                s = [hex(x) for x in bytes(n)]
                for i in range(len(s)):
                    s[i] = int(s[i], 16)
                if len(s) == 32:
                    for i in range(int(len(s) / 4)):
                        addr = s[4 * i]
                        if addr == 128:
                            if s[2] == 0:
                                print("停止状态")
                            elif s[2] == 1:
                                print("启动状态")
                            elif s[2] == 2:
                                print("过流")
                            elif s[2] == 4:
                                print("过压")
                            elif s[2] == 8:
                                print("编码器故障")
                            elif s[2] == 16:
                                print("过热")
                            elif s[2] == 32:
                                print("欠压")
                            elif s[2] == 64:
                                print("过载")
                        elif addr == 225:
                            high_data = s[4 * i + 1]
                            low_data = s[4 * i + 2]
                            self.voltage = high_data * 256 + low_data
                            print("电压:" + str(self.voltage))
                        elif addr == 226:
                            high_data = s[4 * i + 1]
                            low_data = s[4 * i + 2]
                            self.current = (int(high_data * 256 + low_data))/100
                            print("电流:" + str(self.current))
                        elif addr == 228:
                            high_data = s[4 * i + 1]
                            low_data = s[4 * i + 2]
                            self.rel_speed = (int(high_data * 256 + low_data))*6000 / 16384
                            print("转速:" + str(self.rel_speed))
                        elif addr == 230:
                            None
                        elif addr == 231:
                            None
                        elif addr == 232:
                            None
                        elif addr == 233:
                            None
                elif len(s) == 2:
                    if s[0] == 6:
                        print("速度设置成功")
            time.sleep(0.1)

    def send_motor(self):
        while True:
            if self.run:
                self.set_status()
                time.sleep(0.2)
                self.motor_speed_set()
                time.sleep(0.3)


'''
通过a1,a2,a3三个码计算出校验和码
'''


def check_code(a1, a2):
    buffer = struct.pack(">bh", a1, a2)
    buffer = buffer[0] + buffer[1] + buffer[2]
    check_num = (struct.pack(">l", buffer)[-1])
    return check_num


m = SpeedMotor('com4',100)
m.motor_start()
for i in range(100):
    m.set_speed = i
    time.sleep(0.5)
m.motor_stop()