深入分析bgp选路规则(上)

推荐原创

wxs-163 2010-01-19 14:33:11 博主文章分类：CCIE ©著作权

文章标签 职场 bgp route 休闲 rule 文章分类 网络安全

©著作权归作者所有：来自51CTO博客作者wxs-163的原创作品，请联系作者获取转载授权，否则将追究法律责任

一、拓扑图：

二、IBGP邻居学来的信息，不会传递给另外的IBGP邻居，需要再去手动指定邻居，BGP这条路径能不能通，要看这条路径否成为最佳路径和下一跳是否正确与可达：

1、配置各路由器的IP地址以及配置BGP协议。现在来看一下R3的路由表，看到R3能学到全网的路由：

3、再去R4上看一下R4的路由表发现没有学到10.1.255.0/30和130.130.1.0/24这两条路由：

8、但我在R4上traceroute 10.1.255.4之后，发现R4的路由表发生了变化10.1.255.0/30 不存在了。

R4#traceroute 10.1.255.4

Type escape sequence to abort.

Tracing the route to 10.1.255.4

1 10.1.255.9 52 msec 32 msec 16 msec

2 * * *

3 * * *

4 * * *

R4#sh ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/30 is subnetted, 3 subnets

B 10.1.255.4 [200/0] via 10.1.255.9, 00:00:24

C 10.1.255.12 is directly connected, Serial1/1

C 10.1.255.8 is directly connected, Serial1/0

150.150.0.0/24 is subnetted, 1 subnets

B 150.150.1.0 [20/0] via 10.1.255.14, 00:23:42

R4#ping 10.1.255.4

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.1.255.4, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 4/26/52 ms

R4#

(超过8万字一篇发不了。待续，请接着看下篇)

R4#sh ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/30 is subnetted, 3 subnets

B 10.1.255.4 [200/0] via 10.1.255.9, 00:00:21

C 10.1.255.12 is directly connected, Serial1/1

C 10.1.255.8 is directly connected, Serial1/0

150.150.0.0/24 is subnetted, 1 subnets

B 150.150.1.0 [20/0] via 10.1.255.14, 00:02:27

4、终其原因是因为：IBGP对等体学习到的路由，是不会向其它的IBGP对等体通告的。拓扑中的R3从IBGP对等体R4学来的路由是不会向R2这个IBGP对等体通告，同理R3从R2学来的路由也不会向R4通告。所以就造成了R2和R4学不到完整的路由信息。

5、先在R2和R4上互指IBGP邻居，一定要互指，不然邻居不能完全建立起来：

R2(config)#router bgp 64513

R2(config-router)#nei 10.1.255.10 remote 64513

R4(config)#router bgp 64513

R4(config-router)#nei 10.1.255.5 remote 64513

6、相互指定完IBGP邻居之后，用clear ip bgp * 把路由表涮新一下。然后再来看一下R2和R4的路由表：

R2#sh ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/30 is subnetted, 4 subnets

C 10.1.255.4 is directly connected, Serial1/1

C 10.1.255.0 is directly connected, Serial1/0

B 10.1.255.12 [200/0] via 10.1.255.10, 00:00:47

B 10.1.255.8 [200/0] via 10.1.255.6, 00:00:56

130.130.0.0/24 is subnetted, 1 subnets

B 130.130.1.0 [20/0] via 10.1.255.1, 00:00:45

150.150.0.0/24 is subnetted, 1 subnets

B 150.150.1.0 [200/0] via 10.1.255.14, 00:00:24

R2#

R4#sh ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/30 is subnetted, 4 subnets

B 10.1.255.4 [200/0] via 10.1.255.5, 00:00:11

B 10.1.255.0 [200/0] via 10.1.255.5, 00:00:11

C 10.1.255.12 is directly connected, Serial1/1

C 10.1.255.8 is directly connected, Serial1/0

150.150.0.0/24 is subnetted, 1 subnets

B 150.150.1.0 [20/0] via 10.1.255.14, 00:05:26

R4#

7、通过互指邻居，发现R2能学到全网的路由但是R4却不能学到130.130.1.0/24这条路由，而且还发现到10.1.255.4与10.1.255.0 走的都是10.1.255.5。

R4#ping 10.1.255.4

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.1.255.4, timeout is 2 seconds:

..... (发现不通)

Success rate is 0 percent (0/5)

R3#sh ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/30 is subnetted, 4 subnets

C 10.1.255.4 is directly connected, Serial1/0

B 10.1.255.0 [200/0] via 10.1.255.5, 00:07:05

B 10.1.255.12 [200/0] via 10.1.255.10, 00:06:59

C 10.1.255.8 is directly connected, Serial1/1

130.130.0.0/24 is subnetted, 1 subnets

B 130.130.1.0 [200/0] via 10.1.255.1, 00:06:50

150.150.0.0/24 is subnetted, 1 subnets

B 150.150.1.0 [200/0] via 10.1.255.14, 00:06:29

2、去看一下R2的路由表，发现R2没有学到10.1.255.12/24和150.150.1.0/24这两条路由：

R2#sh ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/30 is subnetted, 3 subnets

C 10.1.255.4 is directly connected, Serial1/1

C 10.1.255.0 is directly connected, Serial1/0

B 10.1.255.8 [200/0] via 10.1.255.6, 00:01:16

130.130.0.0/24 is subnetted, 1 subnets

B 130.130.1.0 [20/0] via 10.1.255.1, 00:00:46

上一篇：通过bgp聚合命令来做汇总通告

下一篇：深入分析bgp选路规则(下)

提问和评论都可以，用心的回复会被更多人看到评论

发布评论

相关文章

官方博客	全部文章	热门标签	班级博客
了解我们	网站地图	意见反馈

鸿蒙开发者社区	51CTO学堂
51CTO	软考资讯