作者: 出处:CISCO用户手册
配置一组端口
|
命令 |
目的 |
Step 1 |
configure terminal |
进入配置状态 |
Step 2 |
interface range {port-range} |
进入组配置状态 |
Step 3 |
|
可以使用平时的端口配置命令进行配置 |
Step 4 |
end |
退回 |
Step 5 |
show interfaces [interface-id] |
验证配置 |
Step 6 |
copy running-config startup-config |
保存 |
- 有效的组范围:
- vlan从1 到4094
- fastethernet 槽位/{first port} - {last port}, 槽位为0
- gigabitethernet槽位/{first port} - {last port},槽位为0
- port-channel port-channel-number - port-channel-number, port-channel号从1到64
- 端口号之间需要加入空格,如:interface range fastethernet 0/1 – 5 是有效的,而interface range fastethernet 0/1-5 是无效的.
- interface range 命令只能配置已经存在的interface vlan
- 所有在同一组的端口必须是相同类别的。
Switch# configure terminal
Switch(config)# interface range fastethernet0/1 - 5
Switch(config-if-range)# no shutdown
Switch(config-if-range)#
以下的例子显示使用句号来配置不同类型端口的组:
Switch# configure terminal
Switch(config)# interface range fastethernet0/1 - 3, gigabitethernet0/1 - 2
Switch(config-if-range)# no shutdown
Switch(config-if-range)#
配置二层端口
配置端口速率及双工模式
可以配置快速以太口的速率为10/100Mbps及千兆以太口的速率为10/100/1000-Mbps; 但对于GBIC端口则不能配置速率及双工模式,有时可以配置nonegotiate,当需要联接不支持自适应的其它千兆端口时
|
命令 |
目的 |
Step 1 |
configure terminal |
进入配置状态. |
Step 2 |
interface interface-id |
进入端口配置状态. |
Step 3 |
speed {10 | 100 | 1000 | auto | nonegotiate} |
设置端口速率
注 1000 只工作在千兆口. GBIC模块只工作在1000 Mbps下. nonegotiate 只能在这些GBIC上用 1000BASE-SX, -LX, and -ZX GBIC. |
Step 4 |
duplex {auto | full | half} |
设置全双工或半双工. |
Step 5 |
end |
退出 |
Step 6 |
show interfaces interface-id |
显示有关配置情况 |
Step 7 |
copy running-config startup-config |
保存 |
Switch# configure terminal
Switch(config)# interface fastethernet0/3
Switch(config-if)# speed 10
Switch(config-if)# duplex half
端口描述
|
命令 |
目的 |
Step 1 |
configure terminal |
进入配置模式 |
Step 2 |
interface interface-id |
进入要加入描述的端口 |
Step 3 |
description string |
加入描述 (最多240个字符). |
Step 4 |
end |
退回. |
Step 5 |
show interfaces interface-id description
or
show running-config |
验证. |
Step 6 |
copy running-config startup-config |
保存 |
|
Switch# config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface fastethernet0/4
Switch(config-if)# description Connects to Marketing
Switch(config-if)# end
Switch# show interfaces fastethernet0/4 description
Interface Status Protocol Description
Fa0/4 up down Connects to Marketing
监控及维护端口
监控端口和控制器的状态
Show Commands for Interfaces Command |
目的 |
show interfaces [interface-id] |
显示所有端口或某一端口的状态和配置. |
show interfaces interface-id status [err-disabled] |
显示一系列端口的状态或错误-关闭的状态 |
show interfaces [interface-id] switchport |
显示二层端口的状态,可以用来决定此口是否为二层或三层口。 |
show interfaces [interface-id] description |
显示端口描述 |
show running-config interface [interface-id] |
显示当前配置中的端口配置情况 |
show version |
显示软硬件等情况 |
Switch# show interfaces status
Switch# show interfaces fastethernet 0/1 switchport
Switch# show running-config interface fastethernet0/2
刷新、重置端口及计数器
Clear命令 |
目的 |
clear counters [interface-id] |
清除端口计数器. |
clear line [number | console 0 | vty number] |
重置异步串口的硬件逻辑 |
|
Note clear counters 命令只清除用show interface所显示的计数,不影响用snmp得到的计数 |
Switch# clear counters fastethernet0/5
Clear "show interface" counters on this interface [confirm] y
Switch#
*Sep 30 08:42:55 : %CLEAR-5-COUNTERS: Clear counter on interface FastEthernet0/5
by vty1 (171.69.115.10)
Switch# clear interface fastethernet0/5
关闭和打开端口
|
命令 |
目的 |
Step 1 |
configure terminal |
进入配置状态 |
Step 2 |
interface {vlan vlan-id} | {{fastethernet | gigabitethernet} interface-id} | {port-channel port-channel-number} |
选择要关闭的端口 |
Step 3 |
shutdown |
关闭 |
Step 4 |
end |
退出 |
Step 5 |
show running-config |
验证 |
Switch# configure terminal
Switch(config)# interface fastethernet0/5
Switch(config-if)# shutdown
Switch(config-if)#
Switch# configure terminal
Switch(config)# interface fastethernet0/5
Switch(config-if)# no shutdown
Switch(config-if)#
(完)