RIP用UDP　报文交换路由信息。路由器每３０秒发送一次路由更新通告。如果路由器超过１８０秒没有从另一路由器获得路由更新报文。则认为先前来自那个路由器的路由不能使用。如果在２４０秒任然没有收到更新报文则删除路由RIP的特点：

属于典型的距离向量路由协议。

路由选择的度量值是跳数。最大跳数为15,16 代表无穷大————不可达。

缺省情况下每30秒发送一次路由更新。

支持在多条路径上均衡流量。

RIP1是有类的，不支持CIDR和VLSM；RIP2是无类的支持CIDR和VLSM。

简单的RIP配置：

拓扑图：动态路由RIP的配置_路由

首先对router０进行配置：
 

Router>en
Router#config
Configuring from terminal, memory, or network [terminal]? t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#config ter
%Invalid hex value
Router(config)#inter s1/0
Router(config-if)#ip add 192.168.7.254 255.255.255.0
Router(config-if)#no shutd

%LINK-5-CHANGED: Interface Serial1/0, changed state to down
Router(config-if)#
Router(config-if)#exit
Router(config)#interface Serial1/0
Router(config-if)#clock rate 64000
Router(config-if)#inter s1/1
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shutd

%LINK-5-CHANGED: Interface Serial1/1, changed state to down
Router(config-if)#inter f0/0
Router(config-if)#ip add 192.168.5.254 255.255.255.0
Router(config-if)#no shutd

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 192.168.5.0
Router(config-router)#network 192.168.7.0
Router(config-router)#network 192.168.1.0


 


 

对router１进行配置：



Router>en
Router#config ter
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#inter s1/0
Router(config-if)#ip add 192.168.1.2 255.255.255.0
Router(config-if)#no shutd

%LINK-5-CHANGED: Interface Serial1/0, changed state to up
Router(config-if)#exit
Router(config)#inter s1/0
Router(config-if)#clock rate 64000
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up
Router(config-if)#exit
Router(config)#inter f0/0
Router(config-if)#ip add １７２.168.1.1 255.255.255.0
Router(config-if)#no shutd

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 192.168.1.0
Router(config-router)#network 172.168.１.0
Router(config-router)#

router２进行配置：

Router>en
Router#config ter
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#inter s1/0
Router(config-if)#ip add 192.168.7.21 255.255.255.0
Router(config-if)#no shutd

%LINK-5-CHANGED: Interface Serial1/0, changed state to up
Router(config-if)#in
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to upt
^
% Invalid input detected at '^' marker.

Router(config-if)#inter f0/0
Router(config-if)#ip add 192.168.25.1 255.255.255.0
Router(config-if)#no shutd

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 192.168.7.0
Router(config-router)#network 192.168.25.0
Router(config-router)#

主机pc0ping主机pc1和pc2.

 

动态路由RIP的配置_的_02

http://blog.sina.com.cn/s/blog_8557a3e80100tig1.html

动态路由RIP的配置_动态_03