配置BGP和IGP的交互,可以丰富协议路由表。
组网需求
通信业务的发展,要求能够在广泛的区域实现互访,并且数据传输可靠,中断时间短,这就要求路由的传播区域广,收敛速度快。BGP可以实现路由的高效广泛传播,但是BGP自身不会计算路由。IGP可以实现路由的快速收敛,但是IGP的路由传播效率低,范围小。配置BGP与IGP交互后,IGP路由可以被引入到BGP路由表进行高效广泛的传播,BGP路由也可以被引入到IGP路由表,实现对其他AS的访问。
如图1所示,用户将网络划分为AS65008和AS65009,在AS65009内,使用IGP协议来计算路由(该例使用OSPF做为IGP协议)。为了实现两个AS之间的互访,可以在AS之间配置BGP协议,在AS边缘路由器上配置BGP与IGP交互,这样既可以利用BGP高效的把路由传递到其他AS,也可以把AS外部的路由引入到IGP,实现对AS外部的访问。
配置思路
采用如下的思路配置BGP与IGP交互:
1、在DeviceB和DeviceC上配置OSPF协议。
2、在DeviceA和DeviceB上配置EBGP连接。
3、在DeviceB上配置BGP与OSPF互相引入,查看路由信息。
4、在DeviceB上配置BGP路由聚合,简化BGP路由表。
数据准备
为完成此配置例,需准备如下的数据:
1、DeviceA的Router ID以及所在AS号。
2、DeviceB、DeviceC的Router ID以及所在AS号。
操作步骤
1、配置各接口的IP地址
2、配置OSPF
# 配置DeviceB。
[~DeviceB] ospf 1
[*DeviceB-ospf-1] area 0
[*DeviceB-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.255
[*DeviceB-ospf-1-area-0.0.0.0] commit
[~DeviceB-ospf-1-area-0.0.0.0] quit
[~DeviceB-ospf-1] quit
# 配置DeviceC。
[~DeviceC] ospf 1
[*DeviceC-ospf-1] area 0
[*DeviceC-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.255
[*DeviceC-ospf-1-area-0.0.0.0] network 10.1.2.0 0.0.0.255
[*DeviceC-ospf-1-area-0.0.0.0] commit
[~DeviceC-ospf-1-area-0.0.0.0] quit
[~DeviceC-ospf-1] quit
3、配置EBGP连接
# 配置DeviceA。
[~DeviceA] bgp 65008
[*DeviceA-bgp] router-id 1.1.1.1
[*DeviceA-bgp] peer 172.16.1.1 as-number 65009
[*DeviceA-bgp] ipv4-family unicast
[*DeviceA-bgp-af-ipv4] network 192.168.1.0 255.255.255.0
[*DeviceA-bgp-af-ipv4] commit
# 配置DeviceB。
[~DeviceB] bgp 65009
[*DeviceB-bgp] router-id 2.2.2.2
[*DeviceB-bgp] peer 172.16.1.2 as-number 65008
[*DeviceB-bgp] commit
4、配置BGP与IGP交互
# 在DeviceB上配置BGP引入OSPF路由。
[~DeviceB-bgp] ipv4-family unicast
[*DeviceB-bgp-af-ipv4] import-route ospf 1
[*DeviceB-bgp-af-ipv4] commit
[~DeviceB-bgp-af-ipv4] quit
[~DeviceB-bgp] quit
# 查看DeviceA的路由表。
# 在DeviceB上配置OSPF引入BGP路由。
[~DeviceB] ospf
[*DeviceB-ospf-1] import-route bgp
[*DeviceB-ospf-1] commit
[~DeviceB-ospf-1] quit
显示DeviceC路由表
5、配置路由自动聚合
# 配置DeviceB
[~DeviceB] bgp 65009
[*DeviceB-bgp] ipv4-family unicast
[*DeviceB-bgp-af-ipv4] summary automatic
[*DeviceB-bgp-af-ipv4] commit
# 显示DeviceA的BGP路由表。
使用ping进行验证
使用loopback口建立BGP peer
建立对等体时,当所指定的对等体的IP地址为Loopback接口地址和子接口IP地址时,需要在对等体两端同时配置命令peer connect-interface,以保证两端连接的正确性。
EBGP对等体之间不是直连的物理链路时,则必须使用peer ebgp-max-hop命令允许它们之间经过多跳建立TCP连接。
1、配置各个接口以及loopback接口地址(略)
2、OSPF配置
R4
#
ospf 1
area 0.0.0.0
network 10.1.1.1 0.0.0.0
#
R1
#
ospf 1
area 0.0.0.0
network 1.1.1.1 0.0.0.0
network 10.1.1.2 0.0.0.0
network 10.1.3.1 0.0.0.0
#
R2
#
ospf 1
area 0.0.0.0
network 2.2.2.2 0.0.0.0
network 10.1.3.2 0.0.0.0
network 10.1.2.1 0.0.0.0
#
R3
#
ospf 1
area 0.0.0.0
network 10.1.2.0 0.0.0.255
#
3、BGP配置
R1
#
bgp 65008
router-id 1.1.1.1
peer 2.2.2.2 as-number 65009
peer 2.2.2.2 ebgp-max-hop 255
peer 2.2.2.2 connect-interface LoopBack1
#
ipv4-family unicast
undo synchronization
peer 2.2.2.2 enable
#
R2
#
bgp 65009
router-id 2.2.2.2
peer 1.1.1.1 as-number 65008
peer 1.1.1.1 ebgp-max-hop 255
peer 1.1.1.1 connect-interface LoopBack1
#
ipv4-family unicast
undo synchronization
peer 1.1.1.1 enable
#
return
在R2上看BGP建立状态