第一种方法:系统还可以启动到配置模式时
使用
copy tftp flash
即可升级
//
拷贝
TFTP
服务器上
IOS
到
FLASH
里
<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" />
第二种方法:IOS被删除后的恢复
如果因为误操作将
FLASH
中的
IOS
删除了,原
IOS
中的大部分命令都无法具体的过程如下,那么
ROUTER
将进入
ROM
使用。此时,可以通过
TFTP
服
务器向中存储的基本
IOS
模式,在这种模式下
ROUTER
传输
IOS
,使系统得已恢复。其在一台机器上安装
TFTP
服务器软件,将
IOS
文件放置在
TFTP
服务器的默认根目录下,打开
TFTP
服务器,用控制线将这台机器与
ROUTER
连接起来,另外用交叉网线连接机器的网卡和
ROUTER
的以太口。
(也可以用普通的网线将
ROUTER
和交换机相连再连接机器)做好以上工作后,打开机器的超级终端工具,连接上
ROUTER
,此时窗口中出现的命令行提示
符为
: ROMMON 1 >
(其中
“1”
代表命令行的行数)。在提示符后输入命令:(可以使用
ctrl+break
组合键进入
ROMMON
模式)
ROMMON 1 >IP_ADDRESS=
路由器的
IP
地址(需与
TFTP
服务器在同一网段内)
ROMMON 2 >IP_SUBNET_MASK=
路由器的子网掩码
ROMMON 3 >DEFAUT_GATEWAY=
默认网关地址
(可以没有,也可以是
TFTP
服务器)
ROMMON 4 >TFTP_SERVER= TFTP
服务器
IP
地址
ROMMON 5 >TFTP_FILE= IOS
文件名(只给出文件名,不需要路径)
ROMMON 6 >tftpdnld
回车
注意:前面的几条命令必须使用大写,而最后的
tftpdnld
则要用小写。
在
tftpdnld
命令执行后,只行下,输入
reset
重启
ROUTER
,要根据提示选,就可完成文件的传重启后就又回到了熟悉的
IOS
模式下输。当文件传输完后,将自动回到命令甚至连以前配置的信息都不会丢失。
第三种方法:通过Xmodem升级2610的IOS实例
本篇主要介绍通过
Xmodem
上传
IOS
的过程
,
准备工作,只要有
Cisco
原配的线缆就可以
.
在没有 IOS 的情况下 系统只能进入 Rommon 状态,在这个状态下只能见到如下命令:
rommon 1 > ?
alias set and display aliases command
boot boot up an external process
break set/show/clear the breakpoint
confreg configuration register utility
cont continue executing a downloaded p_w_picpath
context display the context of a loaded p_w_picpath
cookie display contents of cookie PROM in hex
dev list the device table
dir list files in file system
dis display instruction stream
dnld serial download a program module
frame print out a selected stack frame
help monitor builtin command help
history monitor command history
meminfo main memory information
repeat repeat a monitor command
reset system reset
set display the monitor variables
stack produce a stack trace
sync write monitor environment to NVRAM
sysret print out info from last system return
tftpdnld tftp p_w_picpath download
unalias unset an alias
unset unset a monitor variable
xmodem x/ymodem p_w_picpath download
rommon 2 > xmodem -r
会提示如下警告:
WARNING: All existing data in bootflash will be lost!
//警告:在bootflash所有现有的数据将丢失 (实际上就是把以前IOS删掉,把现在的拷贝进去)
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
Ready to receive file ? ...
对于初次做IOS上传,建议不要去修改什么传输速率。传完以后对整个系统初始化 界面如下:
Erasing flash at 0x603c0000
program flash location 0x602f0000
Download Complete!
program load complete, entry point: 0x80008000, size: 0x2f0074
Self decompressing the p_w_picpath : #################################################
################################################################################
################################################################################
################################################################# [OK]
这里说明已经成功了 !!
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 11.3(6)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 06-Oct-98 18:42 by ccai
Image text-base: 0x80008084, data-base: 0x80554578
cisco 2610 (MPC860) processor (revision 0x202) with 12288K/4096K bytes of memory
.
Processor board ID JAB0233005Z (3677578902)
M860 processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
32K bytes of non-volatile configuration memory.
4096K bytes of processor board System flash (Read/Write)
Press RETURN to get started!
00:00:06: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:00:06: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up
00:00:06: %SYS-5-CONFIG_I: Configured from memory by console
00:00:06: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 11.3(6)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 06-Oct-98 18:42 by ccai
00:00:07: %LINEPROTO-5-UPDOWN: Line protocol on
WL_bank_2610_2>Interface Ethernet0/0, changed state to up
00:00:07: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed sta
te to up
00:00:07: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed sta
te to up
2610_2> //
启动完毕
实验完成 !!
转载于:https://blog.51cto.com/justim/240466