Introduction
记录下ASR9001正常启动的log，以备查询.
ASR9001
RP/0/RSP0/CPU0:ASR9001-B#admin reload location all
Sun Oct 14 03:12:32.400 UTC
Preparing system for backup. This may take a few minutes especially for large configurations.
Status report: node0_RSP0_CPU0: START TO BACKUP
Status report: node0_RSP0_CPU0: BACKUP HAS COMPLETED SUCCESSFULLY
[Done]
Proceed with reload? [confirm]RP/0/RSP0/CPU0::This node received reload command. Reloading in 5 secs
reboot internal : cause code 241 cause User initiated forced reload all
reboot_internal timeout 30 is graceful yes
[0x9ebc09f33] Record Reboot History, reboot cause = 0x4000001, descr = Cause: User initiated forced reload all Process: reload Traceback: 70ed0001 f3b25rebooting
颏轈冂H〞脱暤Bootstrap, Version 2.04(20140227:092320) [ASR9K ROMMON],
Copyright (c) 1994-2014 by Cisco Systems, Inc.
Compiled Thu 27-Feb-14 14:53 by nidutta
Starting Initialization of FMAN0
***PPC PROCESSOR REV=2 load FMAN ucode***
Loading ucode for FMAN0, size: 6992, ver: 101.08.00
Starting Initialization of FMAN1
***PPC PROCESSOR REV=2 load FMAN ucode***
Loading ucode for FMAN1, size: 6992, ver: 101.08.00
Serdes Protocol: 0x10
CPU Reset Reason = 0x0001
Initializing GIGE SW...
PPC P40X0 (partnum 0x8023), Revision 02.00, (Core Version 02.00)
Sys Clock: 100 Mhz
Core Clock: 1500 Mhz
Plat Clock: 800 Mhz
LBC Clock: 25 Mhz
MEM Clock: 1300 Mhz
System Bootstrap, Version 2.04(20140227:092320) [ASR9K ROMMON],
Copyright (c) 1994-2014 by Cisco Systems, Inc.
Compiled Thu 27-Feb-14 14:53 by nidutta
Board Type: 0x100401
CPU Board => Rev: 0x3
=========
FPGA ver: 01.0f
CBC: 16.72
DTI programmed with latest image
TIMEX programmed with latest image
MLAN init done: ready to connect to the network
BCM5482PhyInit () : Port 0 --> SFP Not present
BCM5482PhyInit () : Port 1 --> SFP Not present
set_chassis_type: chassis_type=0xef0400 found=TRUE
ASR9001E (P40X0 PPC) RSP platform with 8192 Mb of main memory
program load complete, entry point: 0x100000, size: 0x2ac20
Set baud rate to: 9600
program load complete, entry point: 0x100000, size: 0x2ac20
Set baud rate to: 9600
MBI Candidate = disk0:asr9k-os-mbi-6.1.3/0x100000/mbiasr9k-rp.vm
CARD_SLOT_NUMBER: 0
CPU_INSTANCE: 1
MBI Validation starts ...
Disabling both Mgt LAN ports
Enabling Cluster Port 0 and disabling Port 1
BCM5482 cluster port-1 reset done !!
Port 0. SFP Not Ready (0:0). Init failed
dtsec_init_hw: configuring DTSEC (port 8) for: 1GB, Full Duplex
Interface link changed state to UP.
Interface link state up.
MBI validation sending request.
HIT CTRL-C to abort
.........
No MBI confirmation received from dSC
CARD_SLOT_NUMBER: 0
CPU_INSTANCE: 1
MBI Validation starts ...
Enabling Cluster Port 1 and disabling Port 0
BCM5482 cluster port-0 reset done !!
Port 1. SFP Not Ready (0:0). Init failed
dtsec_init_hw: configuring DTSEC (port 8) for: 1GB, Full Duplex
Interface link changed state to UP.
Interface link state up.
MBI validation sending request.
HIT CTRL-C to abort
..........
No MBI confirmation received from dSC
AUTOBOOT: Boot string = disk0:asr9k-os-mbi-6.1.3/0x100000/mbiasr9k-rp.vm,1;
AUTOBOOT: autobootstate=0, autobootcount=0, cmd=boot disk0:asr9k-os-mbi-6.1.3/0x100000/mbiasr9k-rp.vm
Boot Status 16
program load complete, entry point: 0x100000, size: 0x2ac20
Set baud rate to: 9600
MBI size from header = 21908852,Bootflash resident MBI filesize = 21908852
....................................................................................
program load complete, entry point: 0x204184, size: 0x14e3e74
Boot Status 17
Config = SMP, Running = SMP
Board type: 0x00100401
Card Capability = 0x00000000
################################################################################################################
BSP: Board type : ASR9K-RSP-I
tracelogger: starting tracing in background ring mode
tracelogger running with args: -startring -F 1 -F 2
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS XR Software for the Cisco XR ASR9K, Version 6.1.3
Copyright (c) 2017 by Cisco Systems, Inc.
Oct 14 03:16:15.164: Install Setup: Booting with committed software
Initializing Punt-switch ...
Initializing Punt-switch ...
Set RP CPU Cluster port in DSA mode
Init STP group for Cluster ports forwarding state control done
Cluster: Boot Request Filter configured
Cluster: Control Link monitor proto filter configured
Successfully initialized punt-switch(26 ports).
SPP has connected to PAKMAN....
SPP registered CPU port 4 with DPAA
SPP Port Idx 0 MAC addr --> 00:70:72:00:00:08
RP/0/RSP0/CPU0:Oct 14 03:15:44.935 : imio[64]: %PLATFORM-IMIO-3-OPERATION_NOTIFY : imio_main: cold start
RP/0/RSP0/CPU0:Oct 14 03:17:33.581 : pwr_mgmt[377]: %PLATFORM-PWR_MGMT-2-MODULE_FAILURE : Power-module 0/PS0/M1/SP failure condition raised : Module input voltage out of range
RP/0/RSP0/CPU0:Oct 14 03:17:46.857 : shelfmgr[403]: %PLATFORM-SHELFMGR_HAL-3-POWER_SUPPLY_REDUNDANCY : Power Supplies are not N+1 protected.
RP/0/RSP0/CPU0:Oct 14 03:17:46.883 : envmon[211]: %PLATFORM-ENVMON-2-ENV_CONDITION : Outstanding environmental condition exists in the chassis
ios con0/RSP0/CPU0 is now available
Press RETURN to get started.
SYSTEM CONFIGURATION IN PROCESS
The startup configuration for this device is presently loading.
This may take a few minutes. You will be notified upon completion.
Please do not attempt to reconfigure the device until this process is complete.
User Access Verification
Username: xuxing
Password:
RP/0/RSP0/CPU0:ios#
