拓朴说明：两个路由器全为F0/0相连 第一步：配置R1 R1(config)#ipv6 unicast-routing R1(config)#ipv6 router eigrp 1 R1(config-rtr)#router-id 1.1.1.1 R1(config-rtr)#no sh R1(config)#int f0/0 R1(config-if)#ipv6 eigrp 1 R1(config-if)#ipv6 add 2001::1/64 R1(config-if)#int lo0 R1(config-if)#ipv6 eigrp 1 R1(config-if)#ipv6 add 1::1/64
R1#sh ipv6 int b FastEthernet0/0 [up/up] FE80::C800:CFF:FE34:8 2001::1 FastEthernet0/1 [administratively down/down] Loopback0 [up/up] FE80::C800:CFF:FE34:8 1::1
第二步：配置R2 R2(config)#ipv6 unicast-routing R2(config)#ipv6 router eigrp 1 R2(config-rtr)#router-id 2.2.2.2 R2(config-rtr)#no sh R2(config)#int f0/0 R2(config-if)#ipv6 eigrp 1 R2(config-if)#ipv6 add 2001::2/64 R2(config-if)#int lo0 R2(config-if)#ipv6 eigrp 1 R2(config-if)#ipv6 add 2::2/64
第三步：测试直连 R2#ping 2001::1
Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2001::1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 20/53/124 ms
第四步：ping测试 R1#ping 2::2
Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2::2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/45/120 ms
第五步：show相关 R2#sh ipv6 route IPv6 Routing Table - 6 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route, M - MIPv6 I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 D - EIGRP, EX - EIGRP external D 1::/64 [90/156160] via FE80::C800:CFF:FE34:8, FastEthernet0/0 C 2::/64 [0/0] via ::, Loopback0 L 2::2/128 [0/0] via ::, Loopback0 C 2001::/64 [0/0] via ::, FastEthernet0/0 L 2001::2/128 [0/0] via ::, FastEthernet0/0 L FF00::/8 [0/0] via ::, Null0
R1#sh ipv6 eigrp neighbors IPv6-EIGRP neighbors for process 1 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 Link-local address: Fa0/0 13 00:01:48 395 2370 0 8 FE80::C802:CFF:FE34:8
