<1>配置命令:

(config)#service password-encryption    \\启用加密服务

(config)#no ip domain-lookup   \\关闭域名解析


(config)#line con 0         \\ 进入控制台0口

(config-line)#password 123  \\ 设置控制台密码

(config-line)#login

(config-line)#exec-time 0 0      \\设置超时时间

(config-line)#logging syn           \\输出同步

(config-line)#exit



<2>实验二:

      _________________              __________________

     |   switch1       |4__________5|    switch2       |  

     |_1______2______3_|            |_6_______7______8_|

      /       |       \               /       |       \

     /        |        \             /        |        \

PC:  PC1      PC2       PC3          PC4      PC5       PC6

如图:

要求:1》交换机基本配置。

     2》配置PC1---PC6,

       使用192.168.1.0/24网段内IP地址,

     3》测试PC1---PC6之间是否可以互相PING通






<3>switch密码恢复(注:在实践课里会学习)

 a.断电重启switch后按住mode键,进监控模式

 b.在提示符下输入:

    flash_init        \\初始化Flash文件

    dir flash:        \\显示flash中存储的文件信息

    rename            \\将配置文件重命名

    boot              \\重新启动交换机

 c.开机后,选择"N"不进入setup模式

 d.修改配置文件,并保存配置.

   #show flash:

   #rename

   #conf t

   #enable secret cisco

   #copy running-config startup-config


具体恢复:


Cisco Catalyst 2950/3500/3550交换机密码恢复流程


一、将一台终端或装有超级终端软件的PC接到交换机的console口上。终端参数设置如下:

速率:9600bps

检较位:无

数据位:8

停止位:1

流控:无

二、拨掉电源

三、按住前面板的mode键不放,插上电源,等3-5秒后松开mode键。你会看到如下提示:

The system has been interrupted prior to initializing the flash file system.

The following commands will initialize the flash file system, and finish loading

the operating system software:


flash_init

load_helper

boot

四、输入flash_init

五、输入load _helper

六、输入dir flash:

注意,不要少了flash后面的冒号,屏幕出现如下提示。

Directory of flash:

2 -rwx 843947 Mar 01 1993 00:02:18 C2900XL-c3h2s-mz-12.1-WC5.bin

4 drwx 3776 Mar 01 1993 01:23:24 html

66 -rwx 130 Jan 01 1970 00:01:19 env_vars

68 -rwx 1296 Mar 01 1993 06:55:51 config.text

1728000 bytes total (456704 bytes free)

七、输入rename flash:config.text flash:config.old

八、输入boot引导系统。

九、当出现如下提示时,输入N:

Continue with the configuration dialog? [yes/no] : N

十、用en进入enable状态,并将文件config.old改回config.text,命令如下:

rename flash:config.old flash:config.text

十一、将原配置装入内存,命令如下:

2900# copy flash:config.text system:running-config

十二、修改密码:

2900xl#conf t

2900xl(config)#no enable secret

2900xl(config)#enable secret cisco

2900xl(config)#exit

十三、telnet到交换机上,验证密码是否修改成功

十四、将配置写入nvram

2900xl#write memory


以上步骤中,第十一、十二步需要特别注意,前者是为了保留配置,后者需要注意的是如果不使用no enable secret的话,新密码将不起作用。