一、介绍
 
 
标准区域:默认的区域类型,接收链路更新路由汇总外部路由
 
末节区域:将某区域设为Stub可缩小区域的LSDB,降低内存消耗。阻止LSA4/5进入Stub区域。
成为末节区域的标准:1.必须将Stub区域的所有路由器都配成Stub。 2.Stub区域不能用作虚链路的中转区域。 3.Stub中不能出现ASBR。 4.Area 0不能配成Stub
 
完全末节区域(CISCO私有):更加缩小区域的LSDB,在Stub基础上,阻止LSA3。(阻止LSA3/4/5 ),也会由ABR发出一条LSA3默认路由给Stub的其他路由器。
 
NSSA:只有NSSA区域中才会现LSA7,可以存在ASBR,阻止LSA4/5,ABRLSA7转成LSA5,传播到其他区域,时,ABR也成为了ASBR,因为它也引入了LSA5,其它路由器看到LSA5的通告路由器是ABR
 
 
 
二、在这节我会演示末节与完全末节两个实例
 
实验一:配置OSPF末节区域,在R1上运行RIPOSPF两种路由协议,R1R2属区域0R2R3属区域1IP地址信息如图所示:
 
BSCI—8-(1):OSPF的特殊区域类型与配置(末节与完全末节区域)_cisco stub
步骤一:配置3台路由器,并且发布网段.

R1:
Router>
Router>en
Router#conf t
Router(config)#hostname R1
R1(config-line)#exit
R1(config)#interface f0/0
R1(config-if)#ip address 192.168.1.1 255.255.255.0
R1(config-if)#no sh
R1(config-if)#exit
R1(config)#interface loopback 0
R1(config-if)#ip address 1.1.1.1 255.255.255.0
R1(config-if)#int lo1
R1(config-if)#ip address 1.1.2.1 255.255.255.0
R1(config-if)#exit
R1(config)#router ospf 1     //启用OSPF路由协议
R1(config-router)#network 192.168.1.1 0.0.0.0 area 0
R1(config-router)#exit
R1(config)#router rip     //启用RIP路由协议
R1(config-router)#version 2     //指定版本2
R1(config-router)#no auto-summary     //不要自动汇总
R1(config-router)#network 1.1.1.0     //发布网段
R1(config-router)#network 1.1.2.0
R1(config-router)#end
R1#
 
 
R2:
Router>
Router>en
Router#conf t
Router(config)#hostname R2
R2(config)#interface f0/0
R2(config-if)#ip address 192.168.1.2 255.255.255.0
R2(config-if)#no sh
R2(config-if)#exit
R2(config)#interface f0/1
R2(config-if)#ip address 192.168.2.2 255.255.255.0
R2(config-if)#no sh
R2(config-if)#exit
R2(config)#interface loopback 0
R2(config-if)#ip address 2.2.1.1 255.255.255.0
R2(config-if)#int lo1
R2(config-if)#ip address 2.2.2.1 255.255.255.0
R2(config-if)#exit
R2(config)#router ospf 1     //同上
R2(config-router)#network 192.168.1.2 0.0.0.0 area 0
R2(config-router)#network 192.168.2.2 0.0.0.0 area 1
R2(config-router)#network 2.2.1.1 0.0.0.0 area 0
R2(config-router)#network 2.2.2.1 0.0.0.0 area 0
R2(config-router)#end
R2#
 
 
R3:
Router>
Router>en
Router#conf t
Router(config)#hostname R3
R3(config-line)#exit
R3(config)#interface f0/1
R3(config-if)#ip address 192.168.2.1 255.255.255.0
R3(config-if)#no sh
R3(config-if)#exit
R3(config)#router ospf 1      //同上
R3(config-router)#network 192.168.2.1 0.0.0.0 area 1
R3(config-router)#end
R3#
 

步骤二:在R1上把RIP与OSPF互相重发布,并在R3查看路由表
 
R1(config)#router ospf 1
R1(config-router)#redistribute rip
R1(config-router)#redistribute rip subnets      //把RIP中路由发布进OPSF
R1(config-router)#exit
R1(config)#router rip
R1(config-router)#redistribute ospf 1 metric 1     //把OSPF发布进RIP,度量值为1
R1(config-router)#end
R1#

查看R3路由表:     //学习到2条外部路由,与3条区域间路由.
 
R3#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is not set

     1.0.0.0/24 is subnetted, 2 subnets
O E2    1.1.1.0 [110/20] via 192.168.2.2, 00:00:45, FastEthernet0/1
//E2代表OSPF外部类型2的路由.
O E2    1.1.2.0 [110/20] via 192.168.2.2, 00:00:45, FastEthernet0/1
     2.0.0.0/32 is subnetted, 2 subnets
O IA    2.2.1.1 [110/2] via 192.168.2.2, 00:03:09, FastEthernet0/1
O IA    2.2.2.1 [110/2] via 192.168.2.2, 00:03:09, FastEthernet0/1
O IA 192.168.1.0/24 [110/2] via 192.168.2.2, 00:03:09, FastEthernet0/1
C    192.168.2.0/24 is directly connected, FastEthernet0/1
R3#
 
 
步骤三:下面一步把区域1配置为末节区域,并再查看R3路由。(末节区域能阻止类型4,类型5的LSA,并产生一条OSPF的默认路由)
R2(config)#router ospf 1
R2(config-router)#area 1 stub      //把区域1配置为末节区域

R3(config)#router ospf 1
R3(config-router)#area 1 stub      //同上

查看R3路由表:     //之前的外部E2路由不见了,取而代之的为一条OSPF默认路由.
R3#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is 192.168.2.2 to network 0.0.0.0

     2.0.0.0/32 is subnetted, 2 subnets
O IA    2.2.1.1 [110/2] via 192.168.2.2, 00:01:56, FastEthernet0/1
O IA    2.2.2.1 [110/2] via 192.168.2.2, 00:01:56, FastEthernet0/1
O IA 192.168.1.0/24 [110/2] via 192.168.2.2, 00:01:56, FastEthernet0/1
C    192.168.2.0/24 is directly connected, FastEthernet0/1
O*IA 0.0.0.0/0 [110/2] via 192.168.2.2, 00:01:56, FastEthernet0/1
//带*表示默认路由,O*表示OSPF的默认路由.
R3#
 
 
步骤四:查看R3链路状态数据库是否阻止4/5类LSA,并测试能否拼通.
 
R3#show ip ospf database  //很明显只有前三种LSA,在3类LSA中多了一条默认路由
            OSPF Router with ID (192.168.2.1) (Process ID 1)

                Router Link States (Area 1)

Link ID         ADV Router      Age         Seq#       Checksum Link count
2.2.2.1         2.2.2.1         575         0x80000008 0x0065ff 1
192.168.2.1     192.168.2.1     757         0x80000a52 0x003810 1

                Net Link States (Area 1)
Link ID         ADV Router      Age         Seq#       Checksum
192.168.2.1     192.168.2.1     655         0x80000002 0x009fcd

                Summary Net Link States (Area 1)
Link ID         ADV Router      Age         Seq#       Checksum
192.168.1.0     2.2.2.1         1480        0x80000001 0x00a04c
2.2.1.1         2.2.2.1         1438        0x80000002 0x00143c
2.2.2.1         2.2.2.1         1438        0x80000003 0x000747
0.0.0.0         2.2.2.1         633         0x80000007 0x0051ff
R3#

验证:R3拼R1
R3#ping 1.1.1.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 33/45/64 ms

R3#

总结:因为末节区域阻止了4,5类的LSA,所以它是不能学习到E2,E1的外部路由,之所以最后能拼能R1,是因为末节区域自动加了一条默认路由指向ABR.
 
 
 
实验二:配置OSPF完全末节区域,拓扑如下:
 
BSCI—8-(1):OSPF的特殊区域类型与配置(末节与完全末节区域)_职场_02
 
步骤一:配置3台路由器,并且发布网段.    //与实验一配置一样
步骤二:R1上把RIPOSPF互相重发布,并在R3查看路由表    //与实验一配置一样
步骤三:在R1R3上把区域1改变成完全末节区域,并在R3上查看路由表
R2(config)#router ospf 1
R2(config-router)#area 1 stub no-summary    //把区域1配置为完全末节区域
R3(config)#router ospf 1
R3(config-router)#area 1 stub no-summary    //同上
 
 
查看R3路由表:   //只剩一条区域间的默认路由
R3#show ip route 
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route
Gateway of last resort is 192.168.2.2 to network 0.0.0.0
C    192.168.2.0/24 is directly connected, FastEthernet0/1
O*IA 0.0.0.0/0 [110/2] via 192.168.2.2, 00:02:34, FastEthernet0/1
R3#
 
 
步骤四:查看R3的链路状态数据库,测试拼R1.
 
查看R3链路状态数据库:     //345类型LSA换成一条区域间的默认路由
 
R3#show ip ospf database 
            OSPF Router with ID (192.168.2.1) (Process ID 1)
                Router Link States (Area 1)
Link ID         ADV Router      Age         Seq#       Checksum Link count
2.2.2.1         2.2.2.1         253         0x80000006 0x0087BF 1
192.168.2.1     192.168.2.1     266         0x80000004 0x00116F 1
                Net Link States (Area 1)
Link ID         ADV Router      Age         Seq#       Checksum
192.168.2.1     192.168.2.1     266         0x80000001 0x00C827
                Summary Net Link States (Area 1)
Link ID         ADV Router      Age         Seq#       Checksum
0.0.0.0         2.2.2.1         334         0x80000001 0x007BBB
R3#
R3R1
R3#ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 424/664/1140 ms
R3#
 
实验完成.

本文出自 “梅岩〃s博客” 博客,请务必保留此出处http://justim.blog.51cto.com/740099/271357