思科路由器配置命令大全

思科路由器配置命令大全

  1. switch配置命令 (1)模式转换命令 用户模式----特权模式,使用命令"enable" 特权模式----全局配置模式,使用命令"config t" 全局配置模式----接口模式,使用命令"interface+接口类型+接口号" 全局配置模式----线控模式,使用命令"line+接口类型+接口号" 注: 用户模式:查看初始化的信息. 特权模式:查看所有信息、调试、保存配置信息 全局模式:配置所有信息、针对整个路由器或交换机的所有接口 接口模式:针对某一个接口的配置 线控模式:对路由器进行控制的接口配置 (2)配置命令 show running config 显示所有的配置 show versin 显示版本号和寄存器值 shut down 关闭接口 no shutdown 打开接口 ip add +ip地址 配置IP地址 secondary+IP地址 为接口配置第二个IP地址 show interface+接口类型+接口号 查看接口管理性 show controllers interface 查看接口是否有DCE电缆 show history 查看历史记录 show terminal 查看终端记录大小 hostname+主机名 配置路由器或交换机的标识 config memory 修改保存在NVRAM中的启动配置 exec timeout 0 0 设置控制台会话超时为0 service password-encryptin 手工加密所有密码 enable password +密码 配置明文密码 ena sec +密码 配置密文密码 line vty 0 4/15 进入telnet接口 password +密码 配置telnet密码 line aux 0 进入AUX接口 password +密码 配置密码 line con 0 进入CON接口 password +密码 配置密码 bandwidth+数字 配置带宽 no ip address 删除已配置的IP地址 show startup config 查看NVRAM中的配置信息 copy run-config atartup config 保存信息到NVRAM write 保存信息到NVRAM erase startup-config 清除NVRAM中的配置信息 show ip interface brief 查看接口的谪要信息 banner motd # +信息 + # 配置路由器或交换机的描素信息 description+信息 配置接口听描素信息 vlan database 进入VLAN数据库模式 vlan +vlan号+ 名称 创建VLAN switchport access vlan +vlan号 为VLAN为配接口 interface vlan +vlan号 进入VLAN接口模式 ip add +ip地址 为VLAN配置管理IP地址 vtp+service/tracsparent/client 配置SW的VTP工作模式 vtp +domain+域名 配置SW的VTP域名 vtp +password +密码 配置SW的密码 switchport mode trunk 启用中继 no vlan +vlan号 删除VLAN show spamming-tree vlan +vlan号 查看VLA怕生成树议

  2. 路由器配置命令 ip route+非直连网段+子网掩码+下一跳地址 配置静态/默认路由 show ip route 查看路由表 show protocols 显示出所有的被动路由协议和接口上哪些协议被设置 show ip protocols 显示了被配置在路由器上的路由选择协议,同时给出了在路由选择协议中使用

的定时器 等信息 router rip 激活RIP协议 network +直连网段 发布直连网段 interface lookback 0 激活逻辑接口 passive-interface +接口类型+接口号 配置接口为被动模式 debug ip +协议 动态查看路由更新信息 undebug all 关闭所有DEBUG信息 router eigrp +as号 激活EIGRP路由协议 network +网段+子网掩码 发布直连网段 show ip eigrp neighbors 查看邻居表 show ip eigrp topology 查看拓扑表 show ip eigrp traffic 查看发送包数量 router ospf +process-ID 激活OSPF协议 network+直连网段+area+区域号 发布直连网段 show ip ospf 显示OSPF的进程号和ROUTER-ID encapsulation+封装格式 更改封装格式 no ip admain-lookup 关闭路由器的域名查找 ip routing 在三层交换机上启用路由功能 show user 查看SW的在线用户 clear line +线路号 清除线路

  1. 三层交换机配置命令 配置一组二层端口 configure terminal 进入配置状态 nterface range {port-range} 进入组配置状态 配置三层端口 configure terminal 进入配置状态 interface {{fastethernet | gigabitethernet} interface-id} | {vlan vlan-id} | {port-

channel port-channel-number} 进入端口配置状态 no switchport 把物理端口变成三层口 ip address ip_address subnet_mask 配置IP地址和掩码 no shutdown 激活端口 例: Switch(config)# interface gigabitethernet0/2 Switch(config-if)# no switchport Switch(config-if)# ip address 192.20.135.21 255.255.255.0 Switch(config-if)# no shutdown 配置VLAN configure terminal 进入配置状态 vlan vlan-id 输入一个VLAN号, 然后进入vlan配态,可以输入一个新的VLAN号或旧的来进行修改

。 name vlan-name 可选)输入一个VLAN名,如果没有配置VLAN名,缺省的名字是VLAN号前面用0填满

的4位数,如VLAN0004是VLAN4的缺省名字 mtu mtu-size (可选) 改变MTU大小 例 Switch# configure terminal Switch(config)# vlan 20 Switch(config-vlan)# name test20 Switch(config-vlan)# end 或 Switch# vlan database Switch(vlan)# vlan 20 name test20 Switch(vlan)# exit 将端口分配给一个VLAN configure terminal 进入配置状态 interface interface-id 进入要分配的端口 switchport mode access 定义二层口 switchport access vlan vlan-id 把端口分配给某一VLAN 例 Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface fastethernet0/1 Switch(config-if)# switchport mode access Switch(config-if)# switchport access vlan 2 Switch(config-if)# end Switch# 配置VLAN trunk configure terminal 进入配置状态 interface interface-Id 进入端口配置状态 switchport trunk encapsulation {isl | dot1q | negotiate}配置trunk封装ISL 或 802.1Q 或

自动协商 switchport mode {dynamic {auto | desirable} | trunk} 配置二层trunk模式。 dynamic auto—自动协商是否成为trunk dynamic desirable—把端口设置为trunk如果对方端口是trunk, desirable, 配置Native VLAN

(802.1q) 或自动模式,trunk—设置端口为强制的trunk方式,而不理会对方端口是否为trunk switchport access vlan vlan-id 可选) 指定一个缺省VLAN, 如果此端口不再是trunk switchport trunk native vlan vlan-id 指定802.1Q native VLAN号 例: Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface fastethernet0/4 Switch(config-if)# switchport mode trunk Switch(config-if)# switchport trunk encapsulation dot1q Switch(config-if)# end 定义TRUNK允许的VLAN configure terminal子 进入配置状态 interface interface-id 进入端口配置 switchport mode trunk 配置二层口为trunk switchport trunk allowed vlan {add | all | except | remove} vlan-list可选) 配置trunk允

许的VLAN.使用add, all, except, remove关健字 no switchport trunk allowed vlan 允许所有VLAN通过 例 Switch(config)# interface fastethernet0/1 Switch(config-if)# switchport trunk allowed vlan remove 2 Switch(config-if)# end 配置Native VLAN(802.1q) configure terminal 进入配置状态 interface interface-id 进入配置成802.1qtrunk的端口 switchport trunk native vlan vlan-Id 配置native VLAN号 no switchport trunk native vlan 端口配置命令回到缺省的状态 配置基于端口权值的负载均衡 configure terminal 进入Switch 1配置状态 vtp domain domain-name 配置VTP域 vtp mode server 将Switch 1配置成VTP server. show vtp status 验证VTP的配置 show vlan 验证VLAN configure terminal 进入配置状态 interface fastethernet 0/1 进入F0/1端口 switchport trunk encapsulation {isl | dot1q | negotiate}配置trunk封装 switchport mode trunk 配置成trunk show interfaces fastethernet0/1 switchport 验证VLAN配置 按以上步骤对想要负载均衡的接口进行配置 在另一个交换机上进行此配置 show vlan 当trunk已经起来,在switch2上验证已经学到相的vlan配置 configure terminal 在Switch 1上进入配置状态 interface fastethernet0/1 进入要配置的端口 spanning-tree vlan 8 port-priority 10 将端口权值10赋与VLAN 8. spanning-tree vlan 9 port-priority 10 将端口权值10赋与VLAN 9. spanning-tree vlan 10 port-priority 10 将端口权值10赋与VLAN 10. interface fastethernet0/2 进入F0/2 spanning-tree vlan 3 port-priority 10 将端口权值10赋与VLAN 3. spanning-tree vlan 4 port-priority 10 将端口权值10赋与VLAN 4 spanning-tree vlan 5 port-priority 10 将端口权值10赋与VLAN 5 spanning-tree vlan 6 port-priority 10 将端口权值10赋与VLAN 10 end 退出 show running-config 验证配置 copy running-config startup-config 保存配置

配置STP路径值的负载均衡 Trunk1走VLAN8-10,Trunk2走VLAN2-4

configure terminal 进入 Switch 1配置状态 interface fastethernet 0/1 进入F0/1 switchport trunk encapsulation {isl | dot1q | negotiate}配置封装 switchport mode trunk 配置Trunk,缺省是ISL封装 exit 退回 在F0/2口上重复2-4步骤 exit 退回 show running-config 验证配置 show vlan验证switch1 已经学到Vlan configure terminal 进入配置状态 interface fastethernet 0/1 进入F0/1 spanning-tree vlan 2 cost 30 设置Vlan2生成树路径值为30 spanning-tree vlan 3 cost 30 设置Vlan3生成树路径值为30 spanning-tree vlan 4 cost 30 设置Vlan4生成树路径值为30 end 退出 在switch1的F0/2上重复9-11步骤设置VLAN8,9,10生成树路径值为30 end 退出 show running-config 验证配置 copy running-config startup-config 保存配置

补充:CISCO命令集——路由选择协议及排障 *ip route命令

Router(config)# ip route <目录网络或子网号> [子网掩码] <下一路由器IP地址 | 从本地出口

的地址> [管理距离0~255,默认为1] (注:静态地址配置)

*ip default-network命令

Router(config)# ip default-network <目标网络号> (注:配合路由协使用,用其中的一个动态路由号作默认路由配置) Router(config)# ip route 0.0.0.0 0.0.0.0 <下一路由器IP地址 | 从本地出口的地址> (注:只有一个公网地址时,在出口路由器上的配置)

*内部路由选择协议

*使用router和network命令

Router(config)# router <路由协议rip | igrp | eigrp | ospf | is-is等> [自主系统号] Router(config-router)# network <直接相连的要用此路由协议的网络号> Router(config-router)# network <直接相连的要用此路由协议的网络号>

*路由信息协议RIP

Router(config)# router rip Router(config-router)# network <直接相连的要用rip协议的有类别网络号> Router# show ip protocols Router# show ip route Router# debug ip rip

*内部网关路由协议IGRP

Router(config)# router igrp <自主系统号> Router(config-router)# network <直接相连的要用igrp协议的有类别网络号> Router# show ip interface Router# show ip protocols Router# show ip route Router# debug ip rip

*排除网络故障

排除网络故障的一个总体模型

Router# ping <有故障的主机 | 有故障的IP地址> Router# show ip route Router# show interface <有故障的接口> Router# show run

*IP的故故障排除

检查可用的路由

Router# show ip route <有故障的IP地址> 27.4.4 跟踪路由(Tracing the Route) SUN-A> traceroute <有故障的主机 | 有故障的IP地址> C:\windows> winipcfg C:\windows> ipconfig C:\windows> ipconfig / all C:\windows> tracert <有故障的主机 | 有故障的IP地址>

使用扩展的ping来跟踪连接性

Router# ping

*其它可能的故障

一个地址解析(ARP)的故障

Router# show arp Router# show interface <有故障的接口> C:\windows> arp -a SUN-A> arp –a

验证终端系统的路由表 C:\windows> netstat –rn C:\windows> route –f add 0.0.0.0 mask 0.0.0.0 <需要添加入的网关地址> C:\windows> route [–f ] [[print | add | delete | change] [destination] [mask

netmask] [gateway]] C:\windows> route add mask <网络掩码> <网关ip地址> C:\windows> route delete mask <网络掩码> <网关ip地址> C:\windows> nbtstat <相应的参数> SUN-A> netstat -rn路由器

CISCO交换机配置命令大全2009-08-13 21:131.在基于IOS的交换机上设置主机名/系统名: switch(config)# hostname hostname 在基于CLI的交换机上设置主机名/系统名: switch(enable) set system name name-string

2.在基于IOS的交换机上设置登录口令: switch(config)# enable password level 1 password 在基于CLI的交换机上设置登录口令: switch(enable) set password switch(enable) set enalbepass

3.在基于IOS的交换机上设置远程访问: switch(config)# interface vlan 1 switch(config-if)# ip address ip-address netmask switch(config-if)# ip default-gateway ip-address 在基于CLI的交换机上设置远程访问: switch(enable) set interface sc0 ip-address netmask broadcast-address switch(enable) set interface sc0 vlan switch(enable) set ip route default gateway

4.在基于IOS的交换机上启用和浏览CDP信息: switch(config-if)# cdp enable switch(config-if)# no cdp enable 为了查看Cisco邻接设备的CDP通告信息: switch# show cdp interface [type modle/port] switch# show cdp neighbors [type module/port] [detail] 在基于CLI的交换机上启用和浏览CDP信息: switch(enable) set cdp {enable|disable} module/port 为了查看Cisco邻接设备的CDP通告信息: switch(enable) show cdp neighbors[module/port] [vlan|duplex|capabilities|detail]

5.基于IOS的交换机的端口描述: switch(config-if)# description description-string 基于CLI的交换机的端口描述: switch(enable)set port name module/number description-string

6.在基于IOS的交换机上设置端口速度: switch(config-if)# speed{10|100|auto} 在基于CLI的交换机上设置端口速度: switch(enable) set port speed moudle/number {10|100|auto} switch(enable) set port speed moudle/number {4|16|auto}

7.在基于IOS的交换机上设置以太网的链路模式: switch(config-if)# duplex {auto|full|half} 在基于CLI的交换机上设置以太网的链路模式: switch(enable) set port duplex module/number {full|half}

8.在基于IOS的交换机上配置静态VLAN: switch# vlan database switch(vlan)# vlan vlan-num name vla

switch(vlan)# exit switch# configure teriminal switch(config)# interface interface module/number switch(config-if)# switchport mode access switch(config-if)# switchport access vlan vlan-num switch(config-if)# end 在基于CLI的交换机上配置静态VLAN: switch(enable) set vlan vlan-num [name name] switch(enable) set vlan vlan-num mod-num/port-list

  1. 在基于IOS的交换机上配置VLAN中继线: switch(config)# interface interface mod/port switch(config-if)# switchport mode trunk switch(config-if)# switchport trunk encapsulation {isl|dotlq} switch(config-if)# switchport trunk allowed vlan remove vlan-list switch(config-if)# switchport trunk allowed vlan add vlan-list 在基于CLI的交换机上配置VLAN中继线: switch(enable) set trunk module/port [on|off|desirable|auto|nonegotiate] Vlan-range [isl|dotlq|dotl0|lane|negotiate]

10.在基于IOS的交换机上配置VTP管理域: switch# vlan database switch(vlan)# vtp domain domain-name 在基于CLI的交换机上配置VTP管理域: switch(enable) set vtp [domain domain-name]

11.在基于IOS的交换机上配置VTP 模式: switch# vlan database switch(vlan)# vtp domain domain-name switch(vlan)# vtp {sever|cilent|transparent} switch(vlan)# vtp password password 在基于CLI的交换机上配置VTP 模式: switch(enable) set vtp [domain domain-name] [mode{ sever|cilent|transparent }][password password]

  1. 在基于IOS的交换机上配置VTP版本: switch# vlan database switch(vlan)# vtp v2-mode 在基于CLI的交换机上配置VTP版本: switch(enable) set vtp v2 enable

  2. 在基于IOS的交换机上启动VTP剪裁: switch# vlan database switch(vlan)# vtp pruning 在基于CL I 的交换机上启动VTP剪裁: switch(enable) set vtp pruning enable

14.在基于IOS的交换机上配置以太信道: switch(config-if)# port group group-number [distribution {source|destination}] 在基于CLI的交换机上配置以太信道: switch(enable) set port channel moudle/port-range mode{on|off|desirable|auto}

15.在基于IOS的交换机上调整根路径成本: switch(config-if)# spanning-tree [vlan vlan-list] cost cost 在基于CLI的交换机上调整根路径成本:

switch(enable) set spantree portcost moudle/port cost switch(enable) set spantree portvlancost moudle/port [cost cost][vlan-list]

16.在基于IOS的交换机上调整端口ID: switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority 在基于CLI的交换机上调整端口ID: switch(enable) set spantree portpri {mldule/port}priority switch(enable) set spantree portvlanpri {module/port}priority [vlans]

  1. 在基于IOS的交换机上修改STP时钟: switch(config)# spanning-tree [vlan vlan-list] hello-time seconds switch(config)# spanning-tree [vlan vlan-list] forward-time seconds ` switch(config)# spanning-tree [vlan vlan-list] max-age seconds 在基于CLI的交换机上修改STP时钟: switch(enable) set spantree hello interval[vlan] switch(enable) set spantree fwddelay delay [vlan] switch(enable) set spantree maxage agingtiame[vlan]

  2. 在基于IOS的交换机端口上启用或禁用Port Fast 特征: switch(config-if)#spanning-tree portfast 在基于CLI的交换机端口上启用或禁用Port Fast 特征: switch(enable) set spantree portfast {module/port}{enable|disable}

  3. 在基于IOS的交换机端口上启用或禁用UplinkFast 特征: switch(config)# spanning-tree uplinkfast [max-update-rate pkts-per-second] 在基于CLI的交换机端口上启用或禁用UplinkFast 特征: switch(enable) set spantree uplinkfast {enable|disable}[rate update-rate] [all-protocols off|on]

  4. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个IP地址,然后使用下列命令: switch(config)# cluster enable cluster-name

  5. 为了从一条中继链路上删除VLAN,可使用下列命令: switch(enable) clear trunk module/port vlan-range

  6. 用show vtp domain 显示管理域的VTP参数.

  7. 用show vtp statistics显示管理域的VTP参数.

  8. 在Catalyst交换机上定义TrBRF的命令如下: switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp {ieee|ibm}]

  9. 在Catalyst交换机上定义TrCRF的命令如下: switch (enable) set vlan vlan-num [name name] type trcrf {ring hex-ring-num|decring decimal-ring-num} parent vlan-num

  10. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用如下命令给VLAN分配端口: switch(enable) set vlan vlan-num mod-num/port-num

  11. 命令show spantree显示一个交换机端口的STP状态.

  12. 配置一个ELAN的LES和BUS,可以使用下列命令: ATM (config)# interface atm number.subint multioint ATM(config-subif)# lane serber-bus ethernet elan-name

  13. 配置LECS: ATM(config)# lane database database-name ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address ATM(lane-config-databade)# name …

  14. 创建完数据库后,必须在主接口上启动LECS.命令如下: ATM(config)# interface atm number ATM(config-if)# lane config database database-name ATM(config-if)# lane config auto-config-atm-address

  15. 将每个LEC配置到一个不同的ATM子接口上.命令如下: ATM(config)# interface atm number.subint multipoint ATM(config)# lane client ethernet vlan-num elan-num

  16. 用show lane server 显示LES的状态.

  17. 用show lane bus显示bus的状态.

  18. 用show lane database显示LECS数据库可内容.

  19. 用show lane client显示LEC的状态.

  20. 用show module显示已安装的模块列表.

  21. 用物理接口建立与VLAN的连接: router# configure terminal router(config)# interface media module/port router(config-if)# description description-string router(config-if)# ip address ip-addr subnet-mask router(config-if)# no shutdown

  22. 用中继链路来建立与VLAN的连接: router(config)# interface module/port.subinterface router(config-ig)# encapsulation[isl|dotlq] vlan-number router(config-if)# ip address ip-address subnet-mask

  23. 用LANE 来建立与VLAN的连接: router(config)# interface atm module/port router(config-if)# no ip address router(config-if)# atm pvc 1 0 5 qsaal router(config-if)# atm pvc 2 0 16 ilni router(config-if)# interface atm module/port.subinterface multipoint router(config-if)# ip address ip-address subnet-mask router(config-if)# lane client ethernet elan-num router(config-if)# interface atm module/port.subinterface multipoint router(config-if)# ip address ip-address subnet-name router(config-if)# lane client ethernet elan-name router(config-if)# …

  24. 为了在路由处理器上进行动态路由配置,可以用下列IOS命令来进行: router(config)# ip routing router(config)# router ip-routing-protocol router(config-router)# network ip-network-number router(config-router)# network ip-network-number

  25. 配置默认路由: switch(enable) set ip route default gateway

  26. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令: router(config)# interface interface number router(config-if)# mls rp vlan-id vlan-id-num

  27. 在路由处理器启用MLSP: router(config)# mls rp ip

  28. 为了把一个外置的路由处理器接口和交换机安置在同一个VTP域中: router(config)# interface interface number router(config-if)# mls rp vtp-domain domain-name

  29. 查看指定的VTP域的信息: router# show mls rp vtp-domain vtp domain name

  30. 要确定RSM或路由器上的管理接口,可以在接口模式下输入下列命令: router(config-if)#mls rp management-interface

  31. 要检验MLS-RP的配置情况: router# show mls rp

  32. 检验特定接口上的MLS配置: router# show mls rp interface interface number

  33. 为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表: set mls flow [destination|destination-source|full]

  34. 为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令: router(config)# mls rp ip input-acl

  35. 当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令: switch(enable) set mls enable

  36. 若想改变老化时间的值,可在特权模式下输入以下命令: switch(enable) set mls agingtime agingtime

  37. 设置快速老化: switch(enable) set mls agingtime fast fastagingtime pkt_threshold

  38. 确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定: switch(enable) show mls include

  39. 显示MLS高速缓存记录: switch(enable) show mls entry

  40. 用命令show in arp显示ARP高速缓存区的内容。

  41. 要把路由器配置为HSRP备份组的成员,可以在接口配置模式下使用下面的命令: router(config-if)# standby group-number ip ip-address

  42. 为了使一个路由器重新恢复转发路由器的角色,在接口配置模式下: router(config-if)# standy group-number preempt

  43. 访问时间和保持时间参数是可配置的: router(config-if)# standy group-number timers hellotime holdtime

  44. 配置HSRP跟踪: router(config-if)# standy group-number track type-number interface-priority

  45. 要显示HSRP路由器的状态: router# show standby type-number group brief

  46. 用命令show ip igmp确定当选的查询器。

  47. 启动IP组播路由选择: router(config)# ip muticast-routing

  48. 启动接口上的PIM: dalllasr1>(config-if)# ip pim {dense-mode|sparse-mode|sparse-dense-mode}

  49. 启动稀疏-稠密模式下的PIM: router# ip multicast-routing router# interface type number router# ip pim sparse-dense-mode

  50. 核实PIM的配置: dallasr1># show ip pim interface[type number] [count]

  51. 显示PIM邻居: dallasr1># show ip neighbor type number

  52. 为了配置RP的地址,命令如下: dallasr1># ip pim rp-address ip-address [group-access-list-number][override]

  53. 选择一个默认的RP: dallasr1># ip pim rp-address 通告RP和它所服务的组范围: dallasr1># ip pim send-rp-announce type number scope ttl group-list access-list-number 为管理范围组通告RP的地址: dallasr1># ip pim send-rp-announce ethernet0 scope 16 group-list1 dallasr1># access-list 1 permit 266.0.0.0 0.255.255.255 设定一个RP映像代理: dallasr1># ip pim send-rp-discovery scope ttl 核实组到RP的映像: dallasr1># show ip pim rp mapping dallasr1># show ip pim rp [group-name|group-address] [mapping]

  54. 在路由器接口上用命令ip multicast ttl-threshold ttl-value设定TTL阀值: dallasr1>(config-if)# ip multicast ttl-threshold ttl-value

  55. 用show ip pim neighbor显示PIM邻居表。

  56. 显示组播通信路由表中的各条记录: dallasr1>show ip mroute [group-name|group-address][scoure][summary][count][active kbps]

  57. 要记录一个路由器接受和发送的全部IP组播包: dallasr1> #debug ip mpacket [detail] [access-list][group]

  58. 要在CISCO路由器上配置CGMP: dallasr1>(config-if)# ip cgmp

75.配置一个组播路由器,使之加入某一个特定的组播组: dallasr1>(config-if)# ip igmp join-group group-address

  1. 关闭 CGMP: dallasr1>(config-if)# no ip cgmp

  2. 启动交换机上的CGMP: dallasr1>(enable) set cgmp enable

  3. 核实Catalyst交换机上CGMP的配置情况: catalystla1>(enable) show config set prompt catalystla1> set interface sc0 192.168.1.1 255.255.255.0 set cgmp enable

  4. CGMP离开的设置: Dallas_SW(enable) set cgmp leave

  5. 在Cisco设备上修改控制端口密码: R1(config)# line console 0 R1(config-line)# login R1(config-line)# password Lisbon R1(config)# enable password Lilbao R1(config)# login local R1(config)# username student password cisco

  6. 在Cisco设备上设置控制台及vty端口的会话超时: R1(config)# line console 0 R1(config-line)# exec-timeout 5 10 R1(config)# line vty 0 4 R1(config-line)# exec-timeout 5 2

  7. 在Cisco设备上设定特权级: R1(config)# privilege configure level 3 username R1(config)# privilege configure level 3 copy run start R1(config)# privilege configure level 3 ping R1(config)# privilege configure level 3 show run R1(config)# enable secret level 3 cisco

  8. 使用命令privilege 可定义在该特权级下使用的命令: router(config)# privilege mode level level command

  9. 设定用户特权级: router(config)# enable secret level 3 dallas router(config)# enable secret san-fran router(config)# username student password cisco

  10. 标志设置与显示: R1(config)# banner motd ‘unauthorized access will be prosecuted!’

  11. 设置vty访问: R1(config)# access-list 1 permit 192.168.2.5 R1(config)# line vty 0 4 R1(config)# access-class 1 in

  12. 配置HTTP访问: Router3(config)# access-list 1 permit 192.168.10.7 Router3(config)# ip http sever Router3(config)# ip http access-class 1 Router3(config)# ip http authentication local Router3(config)# username student password cisco

  13. 要启用HTTP访问,请键入以下命令: switch(config)# ip http sever

  14. 在基于set命令的交换机上用setCL1启动和核实端口安全: switch(enable) set port security mod_num/port_num…enable mac address switch(enable) show port mod_num/port_num 在基于CiscoIOS命令的交换机上启动和核实端口安全: switch(config-if)# port secure [mac-mac-count maximum-MAC-count] switch# show mac-address-table security [type module/port]

  15. 用命令access-list在标准通信量过滤表中创建一条记录: Router(config)# access-list access-list-number {permit|deny} source-address [source-address]

  16. 用命令access-list在扩展通信量过滤表中创建一条记录: Router(config)# access-list access-list-number {permit|deny{protocol|protocol-keyword}}{source source-wildcard|any}{destination destination-wildcard|any}[protocol-specific options][log]

  17. 对于带内路由更新,配置路由更新的最基本的命令格式是: R1(config-router)#distribute-list access-list-number|name in [type number]

  18. 对于带外路由更新,配置路由更新的最基本的命令格式是: R1(config-router)#distribute-list access-list-number|name out [interface-name] routing-process| autonomous-system-number

  19. set snmp命令选项: set snmp community {read-only|ready-write|read-write-all}[community_string]

  20. set snmp trap 命令格式如下: set snmp trap {enable|disable} [all|moudle|classis|bridge|repeater| auth|vtp|ippermit|vmps|config|entity|stpx] set snmp trap rvcr_addr rcvr_community

  21. 启用SNMP chassis 陷阱: Console>(enable) set snmp trap enable chassis

  22. 启用所有SNMP chassis 陷阱: Console>(enable) set snmp trap enable

  23. 禁用SNMP chassis 陷阱: Console>(enable) set snmp trap disable chassis

  24. 给SNMP陷阱接收表加一条记录: Console>(enable) set snmp trap 192.122.173.42 public

  25. show snmp 输出结果。

  26. 命令set snmp rmon enable 的输出结果。

  27. 显示SPAN信息: Consile> show span

一些华为路由器命令:

删除设备配置 reset saved-configuration

重启 reboot

看当前配置文件 display current-configuration

改设备名 sysname

保存配置 save

进入特权模式 sysview 华为只有2层模式 不像cisco enale之后还要conf t

定义acl acl nubmere XXXX(3000以上)进入以后 rule permit/deny IP/TCP/UDP等 source XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX(反向) destination XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX(反向) eq 注意 华为默认没有deny any any

防火墙上端口加载ACL [Quidway-Ethernet0/0]firewall packet-filter 3000 inbound

防火墙上新增加用户 local-user XXX(用户名) password simple XXX(密码) local-user XXX service-type ppp

删除某条命令 undo(类似与cisco的no)

静态路由 ip route-static 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX

对vpdn用户设置acl的接口 inte***ce Virtual-Template1

查看路由表 display ip routing-table

设定telnet密码 user-inte***ce vty 0 4 user privilege level 3 set authentication password simple XXX

启动/关闭 启动 un shut 关闭 shut

动态nat设置 acl number 3000 rule 0 permit ip source XXX.XXX.XXX.XXX rule 1 permit ip source XXX.XXX.XXX.XXX rule 2 permit ip source XXX.XXX.XXX.XXX inte***ce Ethernet1/0 des cription ====To-Internet(WAN)==== ip address XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX nat outbound 3000 ipsec policy policy1 利用acl来做 符合acl的IP地址可以出去(注意 此处的ACL隐含了deny any any)不符合的IP地址不可以出去

创建vlan [shzb-crsw-s6506-1]vlan 100 华为vlan不支持name 将port放入vlan 创建了vlan后 进入vlan模式 [shzb-crsw-s6506-1-vlan100]port GigabitEthernet 1/0/1 to GigabitEthernet 1/0/8 表示从G1/0/1 到1/0/8放入VLAN 100

创建trunk inte***ce GigabitEthernet1/0/1 duplex full speed 1000

  • port link-type trunk
  • port trunk permit vlan all port link-aggregation group 1 带*号的是创建trunk链路的语句

vlan地址指定 inte***ce Vlan-inte***ce2 des cription server ip address XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX vrrp vrid 2 virtual-ip XXX.XXX.XXX.XXX vrrp vrid 2 priority 120 vrrp vrid 2 preempt-mode timer delay 10 其中vrrp语句指定vrrp 类似与hsrp 使用vrrp要注意的是华为不支持pvst 只能一台完全是主,一台完全是备份 在主vrrp设备上要指定 stp instance 0 root primary stp TC-protection enable stp enable 在从vrrp设备上要指定 stp instance 0 root secondary stp TC-protection enable stp enable

交换机下面绑acl 首先进入接口模式,输入qos命令 [shzb-crsw-s6506-1-GigabitEthernet1/0/1]qos 在输入如下命令 [shzb-crsw-s6506-1-qoss-GigabitEthernet1/0/1]packet-filter inbound ip-group 3000 华为交换机只能指定inbound方向

启用ospf [shzb-crsw-s6506-1]ospf 100 [shzb-crsw-s6506-1-ospf-100]area 0 [shzb-crsw-s6506-1-ospf-100-area-0.0.0.0]network XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX 配置ospf重发布 [shzb-crsw-s6506-1-ospf-100-area-0.0.0.0]quit [shzb-crsw-s6506-1-ospf-100]import-route static

建立link-group(类似与cisco的channel-group)

link-aggregation group 1 mode manual 然后进入接口 port link-aggregation group 1

启用VRRP之前必须输入 vrrp ping-enable 使得客户能ping网关