华为S5700系列交换机,是我们项目中用的较多的一款,其中24与48口应用较多。现在将华为交换机的一些常用配置整理一下,进行记录。如有错误,请指正。


1 允许telnet(远程登录)

允许华为交换机能telnet,设置密码为Admin@123

telnet server en

#

aaa

authentication-scheme default

authorization-scheme default

accounting-scheme default

domain default

domain default_admin


local-user huawei password cipher Admin@123

local-user huawei privilege level 15

local-user huawei service-type telnet terminal


local-user admin password cipher Admin@123

local-user admin service-type http


#


user-interface con 0

authentication-mode password

set authentication password cipher Admin@123


user-interface vty 0 4

protocol inbound telnet

authentication-mode aaa

user-interface vty 16 20

#


华为S5720S交换机远程登录

telnet server enable


aaa

 authentication-scheme default

 authentication-scheme radius

  authentication-mode radius

 authorization-scheme default

 accounting-scheme default

 local-aaa-user password policy administrator

  password expire 0

 domain default

  authentication-scheme radius

  radius-server default

 domain default_admin

  authentication-scheme default

 local-user admin password irreversible-cipher Admin@123

 local-user admin privilege level 15

 local-user admin service-type terminal http

 local-user huawei password irreversible-cipher Admin@123

 local-user huawei privilege level 15

 local-user huawei service-type telnet terminal


user-interface con 0

authentication-mode password

set authentication password cipher Admin@123


user-interface vty 0 4

protocol inbound telnet

authentication-mode aaa

user-interface vty 16 20

2 创建VLAN


为交换机划分VLAN1001,VLAN1002,

设置vlan1001,接口IP地址为172.16.1.254(即网关地址),子网掩码为255.255.255.0

将g0/0/1~g0/0/24配置为vlan1001

防止arp***


vlan 1001

interface vlan 1001

ip addr 172.16.1.254 24



arp anti-attack gateway-duplicate enable

arp anti-attack rate-limit enable

arp-miss anti-attack rate-limit enable



port-group group1

group-member g0/0/1 to g0/0/24

port link-type access

port default vlan 1001

loopback-detect enable

arp anti-attack rate-limit enable

arp-miss anti-attack rate-limit enable

quit


批量将多个端口添加到Access

port-group group-member  GigabitEthernet0/0/17  to GigabitEthernet0/0/22

port link-type access

port default vlan 2006

quit

3 将多个端口添加到Trunk


将25~44端口划分为Trunk端口


port-group group2

group-member g0/0/25 to g0/0/44

port link-type trunk

port trunk allow-pass vlan 2 to 4094

loopback-detect enable

quit


# 批量将1~16端口添加到Trunk

port-group group-member  GigabitEthernet0/0/1  to GigabitEthernet0/0/16

port link-type trunk

port trunk allow-pass vlan 2 to 4094

quit


4 创建链路聚合端口


将45、46创建链路聚合1,使用RJ45

将47、48创建链路聚合2,使用光纤


clear configuration inte g0/0/45

clear configuration inte g0/0/46

clear configuration inte g0/0/47

clear configuration inte g0/0/48


interface Eth-Trunk1

port link-type trunk

port trunk allow-pass vlan 2 to 4094

mode lacp


interface Eth-Trunk2

port link-type trunk

port trunk allow-pass vlan 2 to 4094

mode lacp



interface GigabitEthernet0/0/45

eth-trunk 1


interface GigabitEthernet0/0/46

eth-trunk 1



interface GigabitEthernet0/0/47

eth-trunk 2

combo-port fiber


interface GigabitEthernet0/0/48

eth-trunk 2

combo-port fiber


【说明】每个端口可能需要执行undo shutdown以激活端口。


5 VLAN端口重新配置为Trunk


原配置如下:

interface GigabitEthernet0/0/17

port link-type access

port default vlan 128


将g0/0/17端口配置为Trunk端口命令

undo port default vlan

undo port link-type


port link-type trunk

port trunk allow-pass vlan all



6 Trunk端口重新配置为VLAN


原配置如下

interface GigabitEthernet0/0/11

port link-type trunk

port trunk allow-pass vlan 2 to 4094


将g0/0/11端口配置为VLAN140命令

undo port trunk allow-pass vlan all

port trunk allow-pass vlan 1

port link-type access

port default vlan 140




7 在交换机上配置DHCP Server


(1)vlan2002的网关地址是172.18.92.254,DHCP地址池中排除172.18.92.200~252、172.18.92.253、DHCP的地址租约是1小时、DNS的地址是172.18.96.1

vlan batch  2001 to 2003


ip pool vlan2002

gateway-list 172.18.92.254

network 172.18.92.0 mask 255.255.255.0

excluded-ip-address 172.18.92.200 172.18.92.253

lease day 0 hour 1 minute 0

dns-list 172.18.96.1

#

interface Vlanif2002

ip address 172.18.92.254 255.255.255.0

dhcp select global

#



8 在交换机中指定WDS服务


如果网络中有WDS(Windows部署服务),如果要为各个VLAN,允许从交换机通过DHCP获得IP地址,并且能从使用其他VLAN中的WDS部署系统(网络拓扑如图所示),则华为交换机DHCP可以进行如下的配置。

本示例配置了VLAN2001~VLAN2006,其中服务器属于VLAN2006,为VLAN2001~2006配置DHCP,并且允许这些VLAN中的计算机,能使用172.18.96.1的WDS安装、部署系统。其中172.18.96.1是Windows Server 2016 数据中心版。


sysname HW5700

#

vlan batch 2001 to 2006

#

ip pool vlan2001

gateway-list 172.18.91.254

network 172.18.91.0 mask 255.255.255.0

dns-list 172.18.96.1

next-server 172.18.96.1

option 66 ip-address 172.18.96.1

option 67 ascii Boot\x86\wdsnbp.com

bootfile Boot\wdsnbp.com

#


interface Vlanif2001

description 1_JiFang

ip address 172.18.91.254 255.255.255.0

dhcp select global

#

#

interface Vlanif2006

description Server

ip address 172.18.96.254 255.255.255.0

dhcp select global

#



9 指定DHCP服务器(在交换机上配置DHCP中继)


【说明】:在交换机上指定DHCP中继(DHCP服务器是Windows Server中的DHCP)这是在早期华为或华三交换机上的配置,具体那个型号我记不清了,现在这些配置我基本上已经不用了,只是在这收集整理一下。

#

dhcp enable

#

dhcp server group dhcpgroup1

dhcp-server 172.30.5.3 0

dhcp-server 172.30.5.15 1


#

interface Vlanif2052

ip address 172.28.52.254 255.255.255.0

dhcp select relay

dhcp relay server-select dhcpgroup1

#


以下是摘录的华为官方帮助文档内容

# 在接口下使能DHCP中继功能。

[SwitchA] dhcp enable //使能DHCP服务,缺省未使能

[SwitchA] interface vlanif 100

[SwitchA-Vlanif100] ip address 10.10.20.1 24

[SwitchA-Vlanif100] dhcp select relay //使能DHCP中继功能,缺省未使能

[SwitchA-Vlanif100] dhcp relay server-ip 192.168.20.2 //配置DHCP中继代理的DHCP服务器的IP地址

[SwitchA-Vlanif100] quit


10 配置静态路由


ip route-static 0.0.0.0 0.0.0.0 172.18.96.253

ip route-static 172.18.0.0 255.255.0.0 172.18.96.251

ip route-static 172.30.30.0 255.255.255.0 172.18.96.250


10 配置SNMP

snmp-agent

snmp-agent local-engineid Admin@123

snmp-agent community write cipher Admin@123

snmp-agent sys-info version all