cisco路由器交换机配置大全

1. switch配置命令

(1)模式转换命令

用户模式----特权模式,使用命令"enable"

特权模式----全局配置模式,使用命令"config t"

全局配置模式----接口模式,使用命令"interface+接口类型+接口号"

全局配置模式----线控模式,使用命令"line+接口类型+接口号"

注:

用户模式:查看初始化的信息.

特权模式:查看所有信息、调试、保存配置信息

全局模式:配置所有信息、针对整个路由器或交换机的所有接口

接口模式:针对某一个接口的配置

线控模式:对路由器进行控制的接口配置

(2)配置命令

show running config 显示所有的配置

show versin 显示版本号和寄存器值

shut down 关闭接口

no shutdown 打开接口

ip add +ip地址 配置IP地址

secondary+IP地址 为接口配置第二个IP地址

show interface+接口类型+接口号 查看接口管理性

show controllers interface 查看接口是否有DCE电缆

show history 查看历史记录

show terminal 查看终端记录大小

hostname+主机名 配置路由器或交换机的标识

config memory 修改保存在NVRAM中的启动配置

exec timeout 0 0 设置控制台会话超时为0

service password-encryptin 手工加密所有密码

enable password +密码 配置明文密码

ena sec +密码 配置密文密码

line vty 0 4/15 进入telnet接口

password +密码 配置telnet密码

line aux 0 进入AUX接口

password +密码 配置密码

line con 0 进入CON接口

password +密码 配置密码

bandwidth+数字 配置带宽

no ip address 删除已配置的IP地址

show startup config 查看NVRAM中的配置信息

copy run-config atartup config 保存信息到NVRAM

write 保存信息到NVRAM

erase startup-config 清除NVRAM中的配置信息

show ip interface brief 查看接口的谪要信息

banner motd # +信息 + # 配置路由器或交换机的描素信息

description+信息 配置接口听描素信息

vlan database 进入VLAN数据库模式

vlan +vlan号+ 名称 创建VLAN

switchport access vlan +vlan号 为VLAN为配接口

interface vlan +vlan号 进入VLAN接口模式

ip add +ip地址 为VLAN配置管理IP地址

vtp+service/tracsparent/client 配置SW的VTP工作模式

vtp +domain+域名 配置SW的VTP域名

vtp +password +密码 配置SW的密码

switchport mode trunk 启用中继

no vlan +vlan号 删除VLAN

show spamming-tree vlan +vlan号 查看VLA怕生成树议

2. 路由器配置命令

ip route+非直连网段+子网掩码+下一跳地址配置静态/默认路由

show ip route 查看路由表

show protocols 显示出所有的被动路由协议和接口上哪些协议被设置

show ip protocols 显示了被配置在路由器上的路由选择协议,同时给出了在路由选择协议中使用

的定时器

等信息

router rip 激活RIP协议

network +直连网段 发布直连网段

interface lookback 0 激活逻辑接口

passive-interface +接口类型+接口号 配置接口为被动模式

debug ip +协议 动态查看路由更新信息

undebug all 关闭所有DEBUG信息

router eigrp +as号 激活EIGRP路由协议

network +网段+子网掩码 发布直连网段

show ip eigrp neighbors 查看邻居表

show ip eigrp topology 查看拓扑表

show ip eigrp traffic 查看发送包数量

router ospf +process-ID 激活OSPF协议

network+直连网段+area+区域号 发布直连网段

show ip ospf 显示OSPF的进程号和ROUTER-ID

encapsulation+封装格式 更改封装格式

no ip admain-lookup 关闭路由器的域名查找

ip routing 在三层交换机上启用路由功能

show user 查看SW的在线用户

clear line +线路号 清除线路

3. 三层交换机配置命令

配置一组二层端口

configure terminal 进入配置状态

nterface range {port-range} 进入组配置状态

配置三层端口

configure terminal 进入配置状态

interface {{fastethernet | gigabitethernet} interface-id} | {vlan vlan-id} | {port-

channel port-channel-number} 进入端口配置状态

no switchport 把物理端口变成三层口

ip address ip_address subnet_mask 配置IP地址和掩码

no shutdown 激活端口

例:

Switch(config)# interface gigabitethernet0/2

Switch(config-if)# no switchport

Switch(config-if)# ip address 192.20.135.21 255.255.255.0

Switch(config-if)# no shutdown

配置VLAN

configure terminal 进入配置状态

vlan vlan-id 输入一个VLAN号, 然后进入vlan配态,可以输入一个新的VLAN号或旧的来进行修改

name vlan-name 可选)输入一个VLAN名,如果没有配置VLAN名,缺省的名字是VLAN号前面用0填满

的4位数,如VLAN0004是VLAN4的缺省名字

mtu mtu-size (可选) 改变MTU大小

Switch# configure terminal

Switch(config)# vlan 20

Switch(config-vlan)# name test20

Switch(config-vlan)# end

Switch# vlan database

Switch(vlan)# vlan 20 name test20

Switch(vlan)# exit

将端口分配给一个VLAN

configure terminal 进入配置状态

interface interface-id 进入要分配的端口

switchport mode access 定义二层口

switchport access vlan vlan-id 把端口分配给某一VLAN

Switch# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)# interface fastethernet0/1

Switch(config-if)# switchport mode access

Switch(config-if)# switchport access vlan 2

Switch(config-if)# end

Switch#

配置VLAN trunk

configure terminal 进入配置状态

interface interface-Id 进入端口配置状态

switchport trunk encapsulation {isl | dot1q | negotiate}配置trunk封装ISL 或 802.1Q 或

自动协商

switchport mode {dynamic {auto | desirable} | trunk} 配置二层trunk模式。

dynamic auto—自动协商是否成为trunk

dynamic desirable—把端口设置为trunk如果对方端口是trunk, desirable, 配置Native VLAN

(802.1q)

或自动模式,trunk—设置端口为强制的trunk方式,而不理会对方端口是否为trunk

switchport access vlan vlan-id 可选) 指定一个缺省VLAN, 如果此端口不再是trunk

switchport trunk native vlan vlan-id 指定802.1Q native VLAN号

例:

Switch# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)# interface fastethernet0/4

Switch(config-if)# switchport mode trunk

Switch(config-if)# switchport trunk encapsulation dot1q

Switch(config-if)# end

定义TRUNK允许的VLAN

configure terminal子 进入配置状态

interface interface-id 进入端口配置

switchport mode trunk 配置二层口为trunk

switchport trunk allowed vlan {add | all | except | remove} vlan-list可选) 配置trunk允

许的VLAN.使用add, all, except, remove关健字

no switchport trunk allowed vlan 允许所有VLAN通过

Switch(config)# interface fastethernet0/1

Switch(config-if)# switchport trunk allowed vlan remove 2

Switch(config-if)# end

配置Native VLAN(802.1q)

configure terminal 进入配置状态

interface interface-id 进入配置成802.1qtrunk的端口

switchport trunk native vlan vlan-Id 配置native VLAN号

no switchport trunk native vlan 端口配置命令回到缺省的状态

配置基于端口权值的负载均衡

configure terminal 进入Switch 1配置状态

vtp domain domain-name 配置VTP域

vtp mode server 将Switch 1配置成VTP server.

show vtp status 验证VTP的配置

show vlan 验证VLAN

configure terminal 进入配置状态

interface fastethernet 0/1 进入F0/1端口

switchport trunk encapsulation {isl | dot1q | negotiate}配置trunk封装

switchport mode trunk 配置成trunk

show interfaces fastethernet0/1 switchport 验证VLAN配置

按以上步骤对想要负载均衡的接口进行配置

在另一个交换机上进行此配置

show vlan 当trunk已经起来,在switch2上验证已经学到相的vlan配置

configure terminal 在Switch 1上进入配置状态

interface fastethernet0/1 进入要配置的端口

spanning-tree vlan 8 port-priority 10 将端口权值10赋与VLAN 8.

spanning-tree vlan 9 port-priority 10 将端口权值10赋与VLAN 9.

spanning-tree vlan 10 port-priority 10 将端口权值10赋与VLAN 10.

interface fastethernet0/2 进入F0/2

spanning-tree vlan 3 port-priority 10 将端口权值10赋与VLAN 3.

spanning-tree vlan 4 port-priority 10 将端口权值10赋与VLAN 4

spanning-tree vlan 5 port-priority 10 将端口权值10赋与VLAN 5

spanning-tree vlan 6 port-priority 10 将端口权值10赋与VLAN 10

end 退出

show running-config 验证配置

copy running-config startup-config 保存配置

配置STP路径值的负载均衡

Trunk1走VLAN8-10,Trunk2走VLAN2-4

configure terminal 进入 Switch 1配置状态

interface fastethernet 0/1 进入F0/1

switchport trunk encapsulation {isl | dot1q | negotiate}配置封装

switchport mode trunk 配置Trunk,缺省是ISL封装

exit 退回

在F0/2口上重复2-4步骤

exit 退回

show running-config 验证配置

show vlan验证switch1 已经学到Vlan

configure terminal 进入配置状态

interface fastethernet 0/1 进入F0/1

spanning-tree vlan 2 cost 30 设置Vlan2生成树路径值为30

spanning-tree vlan 3 cost 30 设置Vlan3生成树路径值为30

spanning-tree vlan 4 cost 30 设置Vlan4生成树路径值为30

end 退出

在switch1的F0/2上重复9-11步骤设置VLAN8,9,10生成树路径值为30

end 退出

show running-config 验证配置

copy running-config startup-config 保存配置

补充:CISCO命令集——路由选择协议及排障

*ip route命令

Router(config)# ip route <目录网络或子网号> [子网掩码] <下一路由器IP地址 | 从本地出口

的地址> [管理距离0~255,默认为1]

(注:静态地址配置)

*ip default-network命令

Router(config)# ip default-network <目标网络号>

(注:配合路由协使用,用其中的一个动态路由号作默认路由配置)

Router(config)# ip route 0.0.0.0 0.0.0.0 <下一路由器IP地址 | 从本地出口的地址>

(注:只有一个公网地址时,在出口路由器上的配置)

*内部路由选择协议

*使用router和network命令

Router(config)# router <路由协议rip | igrp | eigrp | ospf | is-is等> [自主系统号]

Router(config-router)# network <直接相连的要用此路由协议的网络号>

Router(config-router)# network <直接相连的要用此路由协议的网络号>

*路由信息协议RIP

Router(config)# router rip

Router(config-router)# network <直接相连的要用rip协议的有类别网络号>

Router# show ip protocols

Router# show ip route

Router# debug ip rip

*内部网关路由协议IGRP

Router(config)# router igrp <自主系统号>

Router(config-router)# network <直接相连的要用igrp协议的有类别网络号>

Router# show ip interface

Router# show ip protocols

Router# show ip route

Router# debug ip rip

*排除网络故障

排除网络故障的一个总体模型

Router# ping <有故障的主机 | 有故障的IP地址>

Router# show ip route

Router# show interface <有故障的接口>

Router# show run

*IP的故故障排除

检查可用的路由

Router# show ip route <有故障的IP地址>

27.4.4 跟踪路由(Tracing the Route)

SUN-A&gt; traceroute <有故障的主机 | 有故障的IP地址>

C:\windows\&gt; winipcfg

C:\windows\&gt; ipconfig

C:\windows\&gt; ipconfig / all

C:\windows\&gt; tracert <有故障的主机 | 有故障的IP地址>

使用扩展的ping来跟踪连接性

Router# ping

*其它可能的故障

一个地址解析(ARP)的故障

Router# show arp

Router# show interface <有故障的接口>

C:\windows\&gt; arp -a

SUN-A&gt; arp –a

验证终端系统的路由表

C:\windows\&gt; netstat –rn

C:\windows\&gt; route –f add 0.0.0.0 mask 0.0.0.0 <需要添加入的网关地址>

C:\windows\&gt; route [–f ] [[print | add | delete | change] [destination] [mask

netmask] [gateway]]

C:\windows\&gt; route add mask <网络掩码> <网关ip地址>

C:\windows\&gt; route delete mask <网络掩码> <网关ip地址>

C:\windows\&gt; nbtstat <相应的参数>

SUN-A&gt; netstat -rn路由器

CISCO交换机配置命令大全2009-08-13 21:131.在基于IOS的交换机上设置主机名/系统名:

switch(config)# hostname hostname

在基于CLI的交换机上设置主机名/系统名:

switch(enable) set system name name-string

2.在基于IOS的交换机上设置登录口令:

switch(config)# enable password level 1 password

在基于CLI的交换机上设置登录口令:

switch(enable) set password

switch(enable) set enalbepass

3.在基于IOS的交换机上设置远程访问:

switch(config)# interface vlan 1

switch(config-if)# ip address ip-address netmask

switch(config-if)# ip default-gateway ip-address

在基于CLI的交换机上设置远程访问:

switch(enable) set interface sc0 ip-address netmask broadcast-address

switch(enable) set interface sc0 vlan

switch(enable) set ip route default gateway

4.在基于IOS的交换机上启用和浏览CDP信息:

switch(config-if)# cdp enable

switch(config-if)# no cdp enable

为了查看Cisco邻接设备的CDP通告信息:

switch# show cdp interface [type modle/port]

switch# show cdp neighbors [type module/port] [detail]

在基于CLI的交换机上启用和浏览CDP信息:

switch(enable) set cdp {enable|disable} module/port

为了查看Cisco邻接设备的CDP通告信息:

switch(enable) show cdp neighbors[module/port] [vlan|duplex|capabilities|detail]

5.基于IOS的交换机的端口描述:

switch(config-if)# description description-string

基于CLI的交换机的端口描述:

switch(enable)set port name module/number description-string

6.在基于IOS的交换机上设置端口速度:

switch(config-if)# speed{10|100|auto}

在基于CLI的交换机上设置端口速度:

switch(enable) set port speed moudle/number {10|100|auto}

switch(enable) set port speed moudle/number {4|16|auto}

7.在基于IOS的交换机上设置以太网的链路模式:

switch(config-if)# duplex {auto|full|half}

在基于CLI的交换机上设置以太网的链路模式:

switch(enable) set port duplex module/number {full|half}

8.在基于IOS的交换机上配置静态VLAN:

switch# vlan database

switch(vlan)# vlan vlan-num name vla

switch(vlan)# exit

switch# configure teriminal

switch(config)# interface interface module/number

switch(config-if)# switchport mode access

switch(config-if)# switchport access vlan vlan-num

switch(config-if)# end

在基于CLI的交换机上配置静态VLAN:

switch(enable) set vlan vlan-num [name name]

switch(enable) set vlan vlan-num mod-num/port-list

9. 在基于IOS的交换机上配置VLAN中继线:

switch(config)# interface interface mod/port

switch(config-if)# switchport mode trunk

switch(config-if)# switchport trunk encapsulation {isl|dotlq}

switch(config-if)# switchport trunk allowed vlan remove vlan-list

switch(config-if)# switchport trunk allowed vlan add vlan-list

在基于CLI的交换机上配置VLAN中继线:

switch(enable) set trunk module/port [on|off|desirable|auto|nonegotiate]

Vlan-range [isl|dotlq|dotl0|lane|negotiate]

10.在基于IOS的交换机上配置VTP管理域:

switch# vlan database

switch(vlan)# vtp domain domain-name

在基于CLI的交换机上配置VTP管理域:

switch(enable) set vtp [domain domain-name]

1.在基于IOS的交换机上配置VTP 模式:
switch# vlan database
switch(vlan)# vtp domain domain-name
switch(vlan)# vtp {sever|cilent|transparent}
switch(vlan)# vtp password password
在基于CLI的交换机上配置VTP 模式:
switch(enable) set vtp [domain domain-name] [mode{ sever|cilent|transparent }][password password]

12. 在基于IOS的交换机上配置VTP版本:
switch# vlan database
switch(vlan)# vtp v2-mode
在基于CLI的交换机上配置VTP版本:
switch(enable) set vtp v2 enable

13. 在基于IOS的交换机上启动VTP剪裁:
switch# vlan database
switch(vlan)# vtp pruning
在基于CL I 的交换机上启动VTP剪裁:
switch(enable) set vtp pruning enable

14.在基于IOS的交换机上配置以太信道:
switch(config-if)# port group group-number [distribution {source|destination}]
在基于CLI的交换机上配置以太信道:
switch(enable) set port channel moudle/port-range mode{on|off|desirable|auto}

15.在基于IOS的交换机上调整根路径成本:
switch(config-if)# spanning-tree [vlan vlan-list] cost cost
在基于CLI的交换机上调整根路径成本:

switch(enable) set spantree portcost moudle/port cost
switch(enable) set spantree portvlancost moudle/port [cost cost][vlan-list]

16.在基于IOS的交换机上调整端口ID:
switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority
在基于CLI的交换机上调整端口ID:
switch(enable) set spantree portpri {mldule/port}priority
switch(enable) set spantree portvlanpri {module/port}priority [vlans]

17. 在基于IOS的交换机上修改STP时钟:
switch(config)# spanning-tree [vlan vlan-list] hello-time seconds
switch(config)# spanning-tree [vlan vlan-list] forward-time seconds
` switch(config)# spanning-tree [vlan vlan-list] max-age seconds
在基于CLI的交换机上修改STP时钟:
switch(enable) set spantree hello interval[vlan]
switch(enable) set spantree fwddelay delay [vlan]
switch(enable) set spantree maxage agingtiame[vlan]

18. 在基于IOS的交换机端口上启用或禁用Port Fast 特征:
switch(config-if)#spanning-tree portfast
在基于CLI的交换机端口上启用或禁用Port Fast 特征:
switch(enable) set spantree portfast {module/port}{enable|disable}

19. 在基于IOS的交换机端口上启用或禁用UplinkFast 特征:
switch(config)# spanning-tree uplinkfast [max-update-rate pkts-per-second]
在基于CLI的交换机端口上启用或禁用UplinkFast 特征:
switch(enable) set spantree uplinkfast {enable|disable}[rate update-rate] [all-protocols off|on]

20. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个IP地址,然后使用下列命令: switch(config)# cluster enable cluster-name

21. 为了从一条中继链路上删除VLAN,可使用下列命令:
switch(enable) clear trunk module/port vlan-range

22. 用show vtp domain 显示管理域的VTP参数.

23. 用show vtp statistics显示管理域的VTP参数.

24. 在Catalyst交换机上定义TrBRF的命令如下:
switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp {ieee|ibm}]

25. 在Catalyst交换机上定义TrCRF的命令如下:
switch (enable) set vlan vlan-num [name name] type trcrf
{ring hex-ring-num|decring decimal-ring-num} parent vlan-num

26. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用如下命令给VLAN分配端口:
switch(enable) set vlan vlan-num mod-num/port-num

27. 命令show spantree显示一个交换机端口的STP状态.

28. 配置一个ELAN的LES和BUS,可以使用下列命令:
ATM (config)# interface atm number.subint multioint
ATM(config-subif)# lane serber-bus ethernet elan-name

29. 配置LECS:
ATM(config)# lane database database-name
ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address
ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address
ATM(lane-config-databade)# name …

30. 创建完数据库后,必须在主接口上启动LECS.命令如下:
ATM(config)# interface atm number
ATM(config-if)# lane config database database-name
ATM(config-if)# lane config auto-config-atm-address

31. 将每个LEC配置到一个不同的ATM子接口上.命令如下:
ATM(config)# interface atm number.subint multipoint
ATM(config)# lane client ethernet vlan-num elan-num

32. 用show lane server 显示LES的状态.

33. 用show lane bus显示bus的状态.

34. 用show lane database显示LECS数据库可内容.

35. 用show lane client显示LEC的状态.

36. 用show module显示已安装的模块列表.

37. 用物理接口建立与VLAN的连接:
router# configure terminal
router(config)# interface media module/port
router(config-if)# description description-string
router(config-if)# ip address ip-addr subnet-mask
router(config-if)# no shutdown

38. 用中继链路来建立与VLAN的连接:
router(config)# interface module/port.subinterface
router(config-ig)# encapsulation[isl|dotlq] vlan-number
router(config-if)# ip address ip-address subnet-mask

39. 用LANE 来建立与VLAN的连接:
router(config)# interface atm module/port
router(config-if)# no ip address
router(config-if)# atm pvc 1 0 5 qsaal
router(config-if)# atm pvc 2 0 16 ilni
router(config-if)# interface atm module/port.subinterface multipoint
router(config-if)# ip address ip-address subnet-mask
router(config-if)# lane client ethernet elan-num
router(config-if)# interface atm module/port.subinterface multipoint
router(config-if)# ip address ip-address subnet-name
router(config-if)# lane client ethernet elan-name
router(config-if)# …

40. 为了在路由处理器上进行动态路由配置,可以用下列IOS命令来进行:
router(config)# ip routing
router(config)# router ip-routing-protocol
router(config-router)# network ip-network-number
router(config-router)# network ip-network-number

41. 配置默认路由:
switch(enable) set ip route default gateway

42. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令:
router(config)# interface interface number
router(config-if)# mls rp vlan-id vlan-id-num

43. 在路由处理器启用MLSP:
router(config)# mls rp ip

44. 为了把一个外置的路由处理器接口和交换机安置在同一个VTP域中:
router(config)# interface interface number
router(config-if)# mls rp vtp-domain domain-name

45. 查看指定的VTP域的信息:
router# show mls rp vtp-domain vtp domain name

46. 要确定RSM或路由器上的管理接口,可以在接口模式下输入下列命令:
router(config-if)#mls rp management-interface

47. 要检验MLS-RP的配置情况:
router# show mls rp

48. 检验特定接口上的MLS配置:
router# show mls rp interface interface number

49. 为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表:
set mls flow [destination|destination-source|full]

50. 为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令:
router(config)# mls rp ip input-acl

51. 当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令:
switch(enable) set mls enable

52. 若想改变老化时间的值,可在特权模式下输入以下命令:
switch(enable) set mls agingtime agingtime

53. 设置快速老化:
switch(enable) set mls agingtime fast fastagingtime pkt_threshold

54. 确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定:
switch(enable) show mls include

55. 显示MLS高速缓存记录:
switch(enable) show mls entry

56. 用命令show in arp显示ARP高速缓存区的内容。

57. 要把路由器配置为HSRP备份组的成员,可以在接口配置模式下使用下面的命令:
router(config-if)# standby group-number ip ip-address

58. 为了使一个路由器重新恢复转发路由器的角色,在接口配置模式下:
router(config-if)# standy group-number preempt

59. 访问时间和保持时间参数是可配置的:
router(config-if)# standy group-number timers hellotime holdtime

60. 配置HSRP跟踪:
router(config-if)# standy group-number track type-number interface-priority

61. 要显示HSRP路由器的状态:
router# show standby type-number group brief

62. 用命令show ip igmp确定当选的查询器。

63. 启动IP组播路由选择:
router(config)# ip muticast-routing

64. 启动接口上的PIM:
dalllasr1&gt;(config-if)# ip pim {dense-mode|sparse-mode|sparse-dense-mode}

65. 启动稀疏-稠密模式下的PIM:
router# ip multicast-routing
router# interface type number
router# ip pim sparse-dense-mode

66. 核实PIM的配置:
dallasr1&gt;# show ip pim interface[type number] [count]

67. 显示PIM邻居:
dallasr1&gt;# show ip neighbor type number

68. 为了配置RP的地址,命令如下:
dallasr1&gt;# ip pim rp-address ip-address [group-access-list-number][override]

69. 选择一个默认的RP:
dallasr1&gt;# ip pim rp-address
通告RP和它所服务的组范围:
dallasr1&gt;# ip pim send-rp-announce type number scope ttl group-list access-list-number
为管理范围组通告RP的地址:
dallasr1&gt;# ip pim send-rp-announce ethernet0 scope 16 group-list1
dallasr1&gt;# access-list 1 permit 266.0.0.0 0.255.255.255
设定一个RP映像代理:
dallasr1&gt;# ip pim send-rp-discovery scope ttl
核实组到RP的映像:
dallasr1&gt;# show ip pim rp mapping
dallasr1&gt;# show ip pim rp [group-name|group-address] [mapping]

70. 在路由器接口上用命令ip multicast ttl-threshold ttl-value设定TTL阀值:
dallasr1&gt;(config-if)# ip multicast ttl-threshold ttl-value

71. 用show ip pim neighbor显示PIM邻居表。

72. 显示组播通信路由表中的各条记录:
dallasr1&gt;show ip mroute [group-name|group-address][scoure][summary][count][active kbps]

73. 要记录一个路由器接受和发送的全部IP组播包:
dallasr1&gt; #debug ip mpacket [detail] [access-list][group]

74. 要在CISCO路由器上配置CGMP:
dallasr1&gt;(config-if)# ip cgmp

75.配置一个组播路由器,使之加入某一个特定的组播组:
dallasr1&gt;(config-if)# ip igmp join-group group-address

76. 关闭 CGMP:
dallasr1&gt;(config-if)# no ip cgmp

77. 启动交换机上的CGMP:
dallasr1&gt;(enable) set cgmp enable

78. 核实Catalyst交换机上CGMP的配置情况:
catalystla1&gt;(enable) show config
set prompt catalystla1&gt;
set interface sc0 192.168.1.1 255.255.255.0
set cgmp enable

79. CGMP离开的设置:
Dallas_SW(enable) set cgmp leave

80. 在Cisco设备上修改控制端口密码:
R1(config)# line console 0
R1(config-line)# login
R1(config-line)# password Lisbon
R1(config)# enable password Lilbao
R1(config)# login local
R1(config)# username student password cisco

81. 在Cisco设备上设置控制台及vty端口的会话超时:
R1(config)# line console 0
R1(config-line)# exec-timeout 5 10
R1(config)# line vty 0 4
R1(config-line)# exec-timeout 5 2

82. 在Cisco设备上设定特权级:
R1(config)# privilege configure level 3 username
R1(config)# privilege configure level 3 copy run start
R1(config)# privilege configure level 3 ping
R1(config)# privilege configure level 3 show run
R1(config)# enable secret level 3 cisco

83. 使用命令privilege 可定义在该特权级下使用的命令:
router(config)# privilege mode level level command

84. 设定用户特权级:
router(config)# enable secret level 3 dallas
router(config)# enable secret san-fran
router(config)# username student password cisco

85. 标志设置与显示:
R1(config)# banner motd ‘unauthorized access will be prosecuted!’

86. 设置vty访问:
R1(config)# access-list 1 permit 192.168.2.5
R1(config)# line vty 0 4
R1(config)# access-class 1 in

87. 配置HTTP访问:
Router3(config)# access-list 1 permit 192.168.10.7
Router3(config)# ip http sever
Router3(config)# ip http access-class 1
Router3(config)# ip http authentication local
Router3(config)# username student password cisco

88. 要启用HTTP访问,请键入以下命令:
switch(config)# ip http sever

89. 在基于set命令的交换机上用setCL1启动和核实端口安全:
switch(enable) set port security mod_num/port_num…enable mac address
switch(enable) show port mod_num/port_num
在基于CiscoIOS命令的交换机上启动和核实端口安全:
switch(config-if)# port secure [mac-mac-count maximum-MAC-count]
switch# show mac-address-table security [type module/port]

90. 用命令access-list在标准通信量过滤表中创建一条记录:
Router(config)# access-list access-list-number {permit|deny} source-address [source-address]

91. 用命令access-list在扩展通信量过滤表中创建一条记录:
Router(config)# access-list access-list-number {permit|deny{protocol|protocol-keyword}}{source source-wildcard|any}{destination destination-wildcard|any}[protocol-specific options][log]

92. 对于带内路由更新,配置路由更新的最基本的命令格式是:
R1(config-router)#distribute-list access-list-number|name in [type number]

93. 对于带外路由更新,配置路由更新的最基本的命令格式是:
R1(config-router)#distribute-list access-list-number|name out [interface-name] routing-process| autonomous-system-number

94. set snmp命令选项:
set snmp community {read-only|ready-write|read-write-all}[community_string]

95. set snmp trap 命令格式如下:
set snmp trap {enable|disable}
[all|moudle|classis|bridge|repeater| auth|vtp|ippermit|vmps|config|entity|stpx]
set snmp trap rvcr_addr rcvr_community

96. 启用SNMP chassis 陷阱:
Console&gt;(enable) set snmp trap enable chassis

97. 启用所有SNMP chassis 陷阱:
Console&gt;(enable) set snmp trap enable

98. 禁用SNMP chassis 陷阱:
Console&gt;(enable) set snmp trap disable chassis

99. 给SNMP陷阱接收表加一条记录:
Console&gt;(enable) set snmp trap 192.122.173.42 public

100. show snmp 输出结果。

101. 命令set snmp rmon enable 的输出结果。

102. 显示SPAN信息:
Consile&gt; show span

一些华为路由器命令:

删除设备配置
reset saved-configuration

重启
reboot

看当前配置文件
display current-configuration

改设备名
sysname

保存配置
save

进入特权模式
sysview
华为只有2层模式 不像cisco enale之后还要conf t

定义acl
acl nubmere XXXX(3000以上)进入以后
rule permit/deny IP/TCP/UDP等 source XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX(反向)
destination XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX(反向) eq
注意 华为默认没有deny any any

防火墙上端口加载ACL
[Quidway-Ethernet0/0]firewall packet-filter 3000 inbound

防火墙上新增加用户
local-user XXX(用户名) password simple XXX(密码)
local-user XXX service-type ppp

删除某条命令
undo(类似与cisco的no)

静态路由
ip route-static 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX

对vpdn用户设置acl的接口
inte***ce Virtual-Template1

查看路由表
display ip routing-table

设定telnet密码
user-inte***ce vty 0 4
user privilege level 3
set authentication password simple XXX

启动/关闭
启动 un shut
关闭 shut

动态nat设置
acl number 3000
rule 0 permit ip source XXX.XXX.XXX.XXX
rule 1 permit ip source XXX.XXX.XXX.XXX
rule 2 permit ip source XXX.XXX.XXX.XXX
inte***ce Ethernet1/0
des cription ====To-Internet(WAN)====
ip address XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX
nat outbound 3000
ipsec policy policy1
利用acl来做 符合acl的IP地址可以出去(注意 此处的ACL隐含了deny any any)不符合的IP地址不可以出去

创建vlan
[shzb-crsw-s6506-1]vlan 100
华为vlan不支持name
将port放入vlan
创建了vlan后 进入vlan模式
[shzb-crsw-s6506-1-vlan100]port GigabitEthernet 1/0/1 to GigabitEthernet 1/0/8
表示从G1/0/1 到1/0/8放入VLAN 100

创建trunk
inte***ce GigabitEthernet1/0/1
duplex full
speed 1000
* port link-type trunk
* port trunk permit vlan all
port link-aggregation group 1
带*号的是创建trunk链路的语句

vlan地址指定
inte***ce Vlan-inte***ce2
des cription server
ip address XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX
vrrp vrid 2 virtual-ip XXX.XXX.XXX.XXX
vrrp vrid 2 priority 120
vrrp vrid 2 preempt-mode timer delay 10
其中vrrp语句指定vrrp 类似与hsrp
使用vrrp要注意的是华为不支持pvst
只能一台完全是主,一台完全是备份
在主vrrp设备上要指定
stp instance 0 root primary
stp TC-protection enable
stp enable
在从vrrp设备上要指定
stp instance 0 root secondary
stp TC-protection enable
stp enable

交换机下面绑acl
首先进入接口模式,输入qos命令
[shzb-crsw-s6506-1-GigabitEthernet1/0/1]qos
在输入如下命令
[shzb-crsw-s6506-1-qoss-GigabitEthernet1/0/1]packet-filter inbound ip-group 3000
华为交换机只能指定inbound方向

启用ospf
[shzb-crsw-s6506-1]ospf 100
[shzb-crsw-s6506-1-ospf-100]area 0
[shzb-crsw-s6506-1-ospf-100-area-0.0.0.0]network XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX
配置ospf重发布
[shzb-crsw-s6506-1-ospf-100-area-0.0.0.0]quit
[shzb-crsw-s6506-1-ospf-100]import-route static

建立link-group(类似与cisco的channel-group)

link-aggregation group 1 mode manual
然后进入接口
port link-aggregation group 1

启用VRRP之前必须输入
vrrp ping-enable
使得客户能ping网关