Cisco常用命令

switch> 用户模式
1:进入特权模式 enable
switch> enable
switch#
2:进入全局配置模式 configure terminal
switch> enable
switch#c onfigure terminal
switch(conf)#
3:交换机命名 hostname aptech2950 以aptech2950为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch-2950
aptech2950(conf)#
4:配置使能口令 enable password cisco 以cisco为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# enable password cisco
5:配置使能密码 enable secret ciscolab 以cicsolab为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# enable secret ciscolab
6:设置虚拟局域网vlan 1 interface vlan 1
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# interface vlan 1
aptech2950(conf-if)#ip address 192.168.1.1 255.255.255.0 配置交换机端口ip和子网掩码
aptech2950(conf-if)#no shut 是配置处于运行中
aptech2950(conf-if)#exit
aptech2950(conf)#ip default-gateway 192.168.254 设置网关地址
7:进入交换机某一端口 interface fastehernet 0/17 以17端口为例
switch> enable
switch#c onfigure terminal
switch(conf)#hostname aptch2950
aptech2950(conf)# interface fastehernet 0/17
aptech2950(conf-if)#
8:查看命令 show
switch> enable
switch# show version 察看系统中的所有版本信息
show interface vlan 1 查看交换机有关ip 协议的配置信息
show running-configure 查看交换机当前起作用的配置信息
show interface fastethernet 0/1 察看交换机1接口具体配置和统计信息
show mac-address-table 查看mac地址表
show mac-address-table aging-time 查看mac地址表自动老化时间
9:交换机恢复出厂默认恢复命令
switch> enable
switch# erase startup-configure
switch# reload
10:双工模式设置
switch> enable
switch#c onfigure terminal
switch2950(conf)#hostname aptch-2950
aptech2950(conf)# interface fastehernet 0/17 以17端口为例
aptech2950(conf-if)#duplex full/half/auto 有full , half, auto 三个可选项
11:cdp相关命令
switch> enable
switch# show cdp 查看设备的cdp全局配置信息
show cdp interface fastethernet 0/17 查看17端口的cdp配置信息
show cdp traffic 查看有关cdp包的统计信息
show cdp nerghbors 列出与设备相连的cisco设备
12:csico2950的密码恢复
拔下交换机电源线。
用手按着交换机的MODE键,插上电源线
在switch:后执行flash_ini命令:switch: flash_ini
查看flash中的文件: switch: dir flash:
把“config.text”文件改名为“config.old”: switch: rename flash: config.text flash: config.old
执行boot: switch: boot
交换机进入是否进入配置的对话,执行no :
进入特权模式察看flash里的文件: show flash :
把“config.old”文件改名为 “config.text”: switch: rename flash: config.old flash: config.text
把“config.text”拷入系统的“running-configure”: copy flash: config.text system : running-configure
把配置模式重新设置密码存盘,密码恢复成功。
13:交换机telnet远程登录设置:
switch>en
switch#c onfigure terminal
switch(conf)#hostname aptech-2950
aptech2950(conf)#enable password cisco 以cisco为特权模式密码
aptech2950(conf)#interface fastethernet 0/1 以17端口为telnet远程登录端口
aptech2950(conf-if)#ip address 192.168.1.1 255.255.255.0
aptech2950(conf-if)#no shut
aptech2950(conf-if)#exit
aptech2950(conf)line vty 0 4 设置0-4 个用户可以telnet远程登陆
aptech2950(conf-line)#login
aptech2950(conf-line)#password edge 以edge为远程登录的用户密码
主机设置:
ip 192.168.1.2 主机的ip必须和交换机端口的地址在同一网络段
netmask 255.255.255.0
gate-way 192.168.1.1 网关地址是交换机端口地址
运行:
telnet 192.168.1.1
进入telnet远程登录界面
password : edge
aptech2950>en
password: cisco
aptech#
14:交换机配置的重新载入和保存
设置完成交换机的配置后:
aptech2950(conf)#reload
是否保存(y/n) y: 保存设置信息 n:不保存设置信息
路由器命令
router> 用户模式
1:进入特权模式 enable
router > enable
router #
2:进入全局配置模式 configure terminal
router > enable
router #c onfigure terminal
router (conf)#
3:交换机命名 hostname routera 以routerA为例
router > enable
router #c onfigure terminal
router(conf)#hostname routerA
routera (conf)#
4:配置使能口令 enable password cisco 以cisco为例
router > enable
router #c onfigure terminal
router(conf)#hostname routerA
routerA (conf)# enable password cisco
5:配置使能密码 enable secret ciscolab 以cicsolab为例
router > enable
router #c onfigure terminal
router(conf)#hostname routerA
routerA (conf)# enable secret ciscolab
6:进入路由器某一端口 interface fastehernet 0/17 以17端口为例
router > enable
router #c onfigure terminal
router(conf)#hostname routerA
routerA (conf)# interface fastehernet 0/17
routerA (conf-if)#
进入路由器的某一子端口 interface fastethernet 0/17.1 以17端口的1子端口为例
router > enable
router #c onfigure terminal
router(conf)#hostname routerA
routerA (conf)# interface fastehernet 0/17.1
7:设置端口ip地址信息
router > enable
router #c onfigure terminal
router(conf)#hostname routerA
routerA(conf)# interface fastehernet 0/17 以17端口为例
routerA (conf-if)#ip address 192.168.1.1 255.255.255.0 配置交换机端口ip和子网掩码
routerA (conf-if)#no shut 是配置处于运行中
routerA (conf-if)#exit
8:查看命令 show
router > enable
router # show version 察看系统中的所有版本信息
show interface vlan 1 查看交换机有关ip 协议的配置信息
show running-configure 查看交换机当前起作用的配置信息
show interface fastethernet 0/1 察看交换机1接口具体配置和统计信息
show mac-address-table 查看mac地址表
show mac-address-table aging-time 查看mac地址表自动老化时间
show controllers serial + 编号 查看串口类型
show ip router 查看路由器的路由表
9:cdp相关命令
router > enable
router # show cdp 查看设备的cdp全局配置信息
show cdp interface fastethernet 0/17 查看17端口的cdp配置信息
show cdp traffic 查看有关cdp包的统计信息
show cdp nerghbors 列出与设备相连的cisco设备
10:csico2600的密码恢复
重新启动路由器,在启动过程中按下win+break键,使路由器进入rom monitor
在提示符下输入命令修改配置寄存器的值,然后重新启动路由器
remmon1>confreg 0x2142
remmon2>reset
重新启动路由器后进入setup模式,选择“no”,退回到exec模式,此时路由器原有的配置仍然保存在startup-config中,为使路由器恢复密码后配置不变把startup-config中配置保存到running-config中,然后重新设置enable密码,并把配置寄存器改回0x2102:
router>enable
router#copy startup-config running-config
router#c onfigure terminal
router(conf)#enable password cisco
router(conf)#c onfig-register 0x2102
保存当前配置到startup-config , 重新启动路由器。
router #copy running-config startup-config
router #reload
11:路由器telnet远程登录设置:
router>en
router #c onfigure terminal
router (conf)#hostname routerA
routerA (conf)#enable password cisco 以cisco为特权模式密码
routerA (conf)#interface fastethernet 0/1 以17端口为telnet远程登录端口
routerA (conf-if)#ip address 192.168.1.1 255.255.255.0
routerA (conf-if)#no shut
routerA (conf-if)#exit
routerA (conf)line vty 0 4 设置0-4 个用户可以telnet远程登陆
routerA (conf-line)#login
routerA (conf-line)#password edge 以edge为远程登录的用户密码
主机设置:
ip 192.168.1.2 主机的ip必须和交换机端口的地址在同一网络段
netmask 255.255.255.0
gate-way 192.168.1.1 网关地址是交换机端口地址
运行:
telnet 192.168.1.1
进入telnet远程登录界面
password : edge
routera>en
password: cisco
routera#
12:配置路由器的标识 banner $……………$
在全局配置的模式下利用“banner”命令可以配置路由器的提示信息,所有连接到路由器的终端都会收到。
router>en
router #c onfigure terminal
router (conf)#hostname routerA
routerA(conf)#banner motd $This is aptech company’ router ! Please don’t change the configuration without permission!$
13:配置接口标识 description ………
接口标识用于区分路由器的各个接口。
router>en
router #c onfigure terminal
router (conf)#hostname routerA
routerA(conf)#interface fastethernet 0/1 以0/1 接口为例
routerA(conf-if)# description this is a fast Ethernet port used to connecting the company’s intranet!
14:配置超时
超时适用于设置在多长时间没有对console进行配置,自动返回exec会话时间。默认为10分钟。
router>en
router #c onfigure terminal
router (conf)#hostname routerA
routerA(conf)#line console 0
routerA(conf-if)#e xec-timeout 0 0 第一个“0”代表分钟,第二个“0”代表秒
15:配置串口参数
两台路由器通过串口连接需要一个做为DTE,一个做为DCE。DCE设备要向DTE设备提供时钟频率和带宽。
DCE配置:
router>en
router #c onfigure terminal
router (conf)#hostname routerA
routerA(conf)#interface serial 0/0
routerA(conf_if)#clock rate 64000 提供时钟频率为64000
routerA(conf_if)#bandwidth 64 提供带宽为64
DTE配置:路由器串口配置ip地址
router>en
router #c onfigure terminal
router (conf)#hostname routerB
routerB(conf)#interface serial 0/0
routerB(conf_if)#ip address 192.168.1.1 255.255.255.0
16:静态路由的配置
配置路由器A的主机名和接口参数
router>enable
router#c onfigure terminal
router(conf)#hostname routerA
routerA(conf)#interface fastethernet 0/1 路由器A的1端口为两路由器的连接端口
routerA(conf-if)#ip address 192.168.2.1 255.255.255.0
routerA(conf-if)#no shutdown
routerA(conf-if)#exit
routerA(conf)# interface fastethernet 0/0 路由器A的0端口为与主机的连接端口
routerA(conf-if)#ip address 192.168.1.2 255.255.255.0
routerA(conf-if)#no shutdown
主机A的ip地址为 192.168.1.1
255.255.255.0
192.168.1.2
配置路由器B的主机名和接口参数
router>enable
router#c onfigure terminal
router(conf)#hostname routerB
routerB(conf)#interface fastethernet 0/0 路由器B的0端口为两路由器的连接端口
routerB(conf-if)#ip address 192.168.2.2 255.255.255.0
routerB(conf-if)#no shutdown
routerB (conf-if)#exit
routerB(conf)# interface fastethernet 0/1 路由器B的1端口为与主机的连接端口
routerB(conf-if)#ip address 192.168.3.1 255.255.255.0
主机B的ip地址为 192.168.3.2
255.255.255.0
192.168.3.1
配置路由器A的静态路由表
routerA(conf)#ip router 192.168.3.0 255.255.255.0 192.168.2.2
配置路由器B的静态路由表
routerA(conf)#ip router 192.168.1.0 255.255.255.0 192.168.2.1
在routerA和routerB上配置默认路由
routerA(conf)#ip route 0.0.0.0 0.0.0.0 192.168.2.2
routerA(conf)#ip classless
routerB(conf)#ip route 0.0.0.0 0.0.0.0 192.168.2.1
routerB(conf)#ip classless
在routerA和routerB上配置动态路由(RIP)
routerA(conf)#router rip
routerA(conf)#network 192.168.1.0
routerA(conf)#network 192.168.2.0
routerB(conf)# router rip
routerB(conf)#network 192.168.2.0
routerB(conf)#network 192.168.3.0